Woodley InSight V-CHEM Скачать руководство пользователя страница 79

Страница: 79 / 88

If the LED detection is not normal, replace it with a new LED.

Check the connection between the centrifugal motor and Main II board.

Check the connection on the switch board.

8.10

Wi-Fi Cannot be Found

The Wi-Fi connection interface cannot find any connectable signals.

8.10.1

Reasons

Wi-Fi cable is disconnected.

Wi-Fi module is broken.

8.10.2

Troubleshooting

Re-plug the Wi-Fi antenna and test the signal strength.

If it cannot be solved, replace with a new Wi-Fi module.

Replace the Wi-Fi antenna and Main I board.

8.11

Wi-Fi Cannot be Connected

If the Wi-Fi signal fails to connect after a period of time, it may be due to a weak signal

source. A mobile hotspot can be used as an auxiliary method to connect the network.

Содержание InSight V-CHEM

























































































Результаты поиска

Содержание InSight V-CHEM

Отзывы:

Похожие инструкции для InSight V-CHEM

Бренды по названию

Популярные бренды

Woodley InSight V-CHEM, Руководство по обслуживанию

Результаты поиска

Содержание InSight V-CHEM

Отзывы:

Похожие инструкции для InSight V-CHEM

Бренды по названию

Популярные бренды