•
Temperature : You can check the temperature of the HDD mounted in the NVR.
•
Time : Displays the use time of an HDD.
•
Format : Select a device and click on format after which a format confirmation window appears.
Click on the <
OK
> button to format the selected storage device.
J
`
Formatting will delete all the recording data that has been saved. Be careful.
`
While formatting is ongoing, you cannot record video.
`
Do not remove a formatting device until it is finished.
`
After installing an HDD, if the state of use of the HDD is "
Not Defined
", format the HDD before use. (If the warning message
persists after formatting, replace the HDD with a new one)
•
ARB : Video that was not recorded due to a camera disconnection can be backed up after the connection
with the camera is re-established. Press the button and an <
Auto Recovery Backup
> window is opened.
- For ARB storage : Select a storage device to be set to ARB.
- Select ARB channel : Select a channel to run the ARB.
`
You can select multiple channels.
If you select <
All CHs
>, all channels will be selected.
- ARB bandwidth : Select a bandwidth for the ARB function.
M
`
Only our camera products (SUNAPI version 2.3.2 or higher) support the ARB function. To use this function, the camera will
need to record video on the SD card.
`
The maximum bit rate value for the profile used in camera SD card recording should be set to under 6144kbps. The detailed
information on how to set the profile for SD card recording can be found in the camera manual.
`
To use the ARB function correctly, both the camera and NVR should be time synchronized with the time server. (Page 26)
`
ARB function is activated when NVR starts/when the channel camera set is reconnected/when an NVR recording missing
section recurs at regular intervals after NVR starts.
`
NVR recording missing section that can be restored with the ARB function is for 24 hours backwards from the point when the
ARB function is activated.
`
You can check which channels have ARB function activated through the message on each channel screen that is displayed
when selecting a channel. (Page 19)
•
HDD Map : You can check the location according to the assigned number for the HDDs installed inside.
(XRN-810S)
`
Refer to this when servicing or installing an additional HDD.
J
`
Do not add or remove an HDD while NVR is running.
HDD Alarm Setting
For HDD malfunctions, you can set the inspection alarm output terminal, the replacement alarm output terminal
and the alarm time.
[
MENU
]
Ö
[
ENTER
]
Ö
▼
Ö
<
Menu
>
Ö
[
ENTER
]
Ö
▼
Ö
<
Device
>
Ö
►▼
Ö
<
Storage Device
>
Ö
[
ENTER
]
Ö
▼►
Ö
<
HDD Alarm
>
Ö
[
ENTER
]
Ö
▲▼◄►
Ö
[
ENTER
]
• Alarm
- If <
All
> was selected, both beep sound and alarm signal through rear side ports will output.
- If <
BEEP
> was selected, a beep will sound.
- Alarm signal will output through the alarm out port on the rear side when selected <
1
>, <
2
>, <
3
>.
• Check Alarm Output Port : If HDD generates check alarm, the alarm signal will output to the specified alarm
output port.
• Replace Alarm Output Port : If HDD generates replace alarm, the alarm signal will output to the specified
alarm output port.
• Duration : Sets the alarm duration for the alarm signal and beep sound.
M
`
<
Check
> status means that the HDD is operating but it has problems that require technical examination.
(
) appears on the Live screen.
`
<
Replace
> status means that the HDD has defect and requires immediate replacement.
(
) appears on the Live screen.
38_
menu setup
menu setup
