SmartPAC 2 with WPC 2000 Integration User Manual
1128600
Reporting Downtime and Scrap to SFC
H-11
UNPLANNED RESET
STROKES
PLANNED RESET
STROKES
CHANGEOVER RESET
STROKES
Specifies the number of strokes that must occur after the press
is restarted following a period of Unplanned Downtime,
Planned Downtime, or Changeover Time before SFC begins
documenting the machine state as “Running Time.” This
setting prevents additional press time from being attributed to
a downtime reason when the operator forgets to select the
“BACK ON LINE” item from the Dialog Menu. The number of
strokes you specify should be the maximum number of press
cycles that are likely to be needed to return the press to
production. Valid entries: 1-9999. Suggested settings:
Set the Unplanned Reset Strokes counter to two strokes more
than the maximum number of strokes required to fill an empty
die. This setting should give the operator sufficient time to
complete a response to the downtime cause (such as Coil
Change) that requires the longest time to address.
Set the Planned Reset Strokes counter to the lowest number
of strokes required to return the press to production following a
lunch or other break.
Set the Changeover Reset Strokes counter to the maximum
number of strokes required to complete a die setup.
SINGLE STROKE MODE
This setting, which is used for hand-fed applications when the
press is being run in Single-stroke mode, indicates whether
SFC counts press cycles (or parts made) within the period
specified in the IDLE TIMER field (see next entry) to determine
whether the press is “running.” When this field is set to
“ENABLED,” SFC only documents the press as “Idle” when no
cycles occur (i.e., no parts are made) during an Idle Timer
period. There are two settings:
ENABLED Single-stroke Mode enabled
DISABLED Single-stroke Mode disabled
IDLE TIMER
Specifies the number of seconds during which SmartPAC 2
counts the number of press strokes in Single-stroke mode to
determine a production rate for hand-fed applications. This
value should be twice the cycle time for the slowest hand-fed
job run on a press. For example, if the slowest job produces
an average of 6 parts per minute, the Idle Timer should be set
to 20 seconds (6 parts per minute = 10-second cycle time; 2 x
10 seconds = 20 seconds). Available selections: 5, 10, 15, 20,
30, and 60.
Table H-1. Set Communications Menu Settings (Cont.)
Field
Settings
Содержание SmartPAC 2
