1128600
SmartPAC 2 with WPC 2000 Integration User Manual
2-102
Installation
11.
Go to the next applicable test.
Single Stroke Mode Test without Light Curtain(s)
To test Single-stroke mode when light curtains are not installed, perform the following steps,
referring to Figure 2-41 for LED locations and
, page 4-44 for instructions in how
to access the Input Status screens:
1.
On the SmartPAC 2 front panel:
•
Turn the Program/Run key switch to RUN.
•
Turn the Stroke Select key switch of OFF.
•
Select TWO HAND on the Mode Select Menu (see page 6-40)
•
Turn the Stroke Select key switch to SINGLE STROKE.
Verify that the “S.S. SEL” item on the WPC Buttons and Switches Input Status screen is
ON (see Figure 4-26, page 4-45).
2.
Press and hold both Run/Inch palm buttons, observing the motion of the ram.
•
If the ram makes a complete stroke and stops at or near top dead center, go to step 6.
•
If the ram does not make a full stroke or does not stop at top dead center, go to the next
step.
3.
Check for fault codes on the SmartPAC 2 display.
•
If a fault code between F80 and F89 (or between H80 and H89) displays, there is a
problem with the overrun limit switch. Try the remedies suggested for overrun limit
switch faults, starting on page 7-21; then, inch the ram to the top of the stroke and run
the test again, starting with step 2. If the ram still does not make a complete stroke or
does not stop at top dead center, call Wintriss Tech. Support.
•
If the SmartPAC 2 display shows no error or an error other than an overrun limit switch
fault, check and correct the wiring of the palm buttons and light curtains, correcting any
problems; then, run the test again, starting with step 2. If the ram still does not complete
a stroke or stop at top dead center, call Wintriss Tech. Support.
INJURY DURING TESTING
• Keep all personnel away from the press during testing.
• Be sure there is no die or other tooling in the press during testing.
Failure to comply with these instructions will result in death or serious injury.
CONTINUOUS MODE USED ON PRESS NOT GUARDED PROPERLY FOR CONTINUOUS
Disconnect the “Continuous” position on the Stroke Select switch to prevent your press from being
run in Continuous mode if it is not guarded correctly for use in Continuous mode. Also cover the
“CONT” label on your control’s Stroke Select switch.
Failure to comply with these instructions will result in death or serious injury.
DANGER
!
DANGER
!
Содержание SmartPAC 2
