WinGD X72-B страница 476 Скачать руководство пользователя | Manualshive

Страница: 476 / 526

background image

10.22

Special running condition: Cylinder cut out

The engine is designed to run with all its cylinders working. If a cylinder stops working, it must be
repaired as soon as possible. However, if it is impossible to repair the not working cylinder, then
the engine can still be run as long as only 1 or 2 cylinders are not working. This is called cylinder
cut out operation and it is considered a special running condition.

WARNING

The special running condition of the cylinder cut out is only available in diesel mode.

WARNING

Running the engine under a special running condition will impact the following parameters
negatively:

•

Increase of Thermal load

•

Increase of exhaust temperature

•

Increase of torsional vibrations

•

Increase of stress on the Crankshaft

•

Reduction of engine revolutions

•

Reduction of load limit

•

Occurance of Surging

WARNING

If 2 or more cylinders are misfiring, Contact WinGD immediately.

WARNING

Running the engine under special running conditions for more than 2-5 days can damage
the engine. If the engine is run under special running conditions for more than that, contact
the engine builder to obtain advice.

NOTE:

If only the fuel for the respective cylinders is cut off, while the same time, the starting air
connections remain intact, then the engine remains fully maneuverable.

NOTE:

If the starting air supply is cut off to some cylinders, the engine might not start from all
crankshaft positions. This can be resolved by starting the engine in reverse it or by using
the turning gear to change the starting position.

There are 5 different procedures of cutting a single cylinder out of operation. If it is needed, each
procedure can be repeated to cut of a second cylinder. The correct procedure depends on the
circumstances of under which the cylinder is underperforming, so chose the procedure best fitting
for the circumstances. The 5 procedures are:

•

A.) Cylinder cut out while the piston and exhaust valve are still working and the compression
is still on

•

B.) Cylinder cut out while the piston and exhaust valve are still working and the compression
is off

•

C.) Cylinder cut out while the piston is still moving but the exhaust valve is closed and the
compression is on

X72-B

AA00-0000-00AAA-100A-A

Operation Manual

Special running condition: Cylinder cut out

Winterthur Gas & Diesel Ltd.

- 476 -

Issue 003 2021-12

«
...
474
475
476
477
478
...
»

Содержание X72-B















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X72-B

Бренд: YuanDong Страницы: 23

Бренд: FAAC Страницы: 124

Бренд: Kober Страницы: 112

Бренд: Viessmann Страницы: 14

Бренд: Bison Страницы: 19

Бренд: cemp Страницы: 18

Бренд: Leadshine Technology Страницы: 55

EASY-KART 100cc

Бренд: IAME Страницы: 35

Бренд: ARRI Страницы: 28

Enduro RR 350 2015

Бренд: Beta Страницы: 158

Бренд: Fagor Страницы: 174

Бренд: Detroit Diesel Страницы: 83

Series 60 DDEC VI

Бренд: Detroit Diesel Страницы: 402

Бренд: Honda Страницы: 60

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: Baumuller Страницы: 26

Бренд: Baumuller Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды