WinGD X72-B страница 463 Скачать руководство пользователя

Страница: 463 / 526

Indication on LDU

Possible cause

Procedure

SCR CAN failure

SCR system does not receives CAN
signal.

•

Re-establish the cabling of
X24-5/6 to the MCM E70.

NOTE:

This is only applicable
to SCR systems with
CAN interface.

Communication to ECS fail

ECS does not receive CAN interface
signals.

•

Re-establish the cabling X34-5/6
to MCM E70.

For WECS:

•

Re-establish the cabling CAN-M
X22-55/56 to FCM 20.3.

For UNIC:

•

Re-establish the cabling CAN 3
X21-2/3 to LDU-20.

CAN interface failure LDU
ECR

CAN interface failure to LDU ECR.

•

Reboot the LDU local and LDU
ECR.

•

Re-establish the cabling CAN#2
X22-5/6 to the LDU local E71.

•

Re-establish the cabling CAN#3
X21-2/3 to the LDU ECR E72.

Tab 10-65 Urea dosing failure

Indication on LDU

Possible cause

Procedure

Urea dosing system Setpoint
failed

Status bit for hardware signal failure:
Urea dosing setpoint.

NOTE:

This failure can occur due
to short circuit or wire
break.

•

Re-establish the wiring between
E70 and external dosing system.

Urea feedback input failed

Status bit for hardware signal failure:
Urea feedback.

NOTE:

This failure can occur due
to short circuit or wire
break.

•

Re-establish the wiring between
E70 and external dosing system.

Dosing system not ready

SCR system sent a signal that urea
dosing system is not ready.

•

Do a check of the external SCR
control system.

Tab 10-66 Temperature sensor failure

Indication on LDU

Possible cause

Procedure

TE3746C

Temperature sensor fails to mea-
sure the exhaust gas temperature at
SCR reactor outlet.

Status bit for hardware signal failure:
Temperature sensor TE3746C.

•

Re-establish the cabling X41-1/2
to MCM E70.

•

Replace the faulty sensor if re-
quired.

X72-B

AA00-0000-00AAD-410A-A

Operation Manual

LP SCR - Alarm failure troubleshooting

Winterthur Gas & Diesel Ltd.

- 463 -

Issue 003 2021-12

Содержание X72-B















































































































































































































































































































































































































































































































































Результаты поиска

Содержание X72-B

Отзывы:

Похожие инструкции для X72-B

Бренды по названию

Популярные бренды

WinGD X72-B, Руководство по эксплуатации

Результаты поиска

Содержание X72-B

Отзывы:

Похожие инструкции для X72-B

Бренды по названию

Популярные бренды