WinGD X72-B Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 526

WinGD X72-B Скачать руководство пользователя страница 47

WARNING

Injury hazard: The removal of fuel valves or other valves in the cylinder cover can cause
the oil to fall on the piston crown. If the piston is hot this can cause explosion. Make sure
that the engine is cool down before maintenance.

WARNING

Injury hazard: Do not touch the spray holes during the function test of the fuel valves. The
sudden release of oil can cause injury to personal. Always use the correct personal
protective equipment.

WARNING

Injury hazard: Make sure that the engine is stop and the current is switch-off from the main
switch before maintenance work starts. The drain valve must be open and decrease the
pressure to 0 bar during the maintenance procedure.

WARNING

Injury hazard: Before disassembly of the part from the system Check and release the
pressure of the related system. injury to personnel can occur.

WARNING

Injury hazard: Do not repair the hydraulic servo oil or rail system, when pumps are in
operation. Injury to personnel can occur.

WARNING

Injury hazard: Do not stand near the crankcase doors, engine room casing doors or relief
valves when the alarm is active for oil mist, high lube oil temperature, no piston colling oil
flow or scavenge box fire. Injury to personnel can occur.

CAUTION

Damage hazard: Always replace the damaged sealing materials with new sealing materials.
Do not try to repair them.

CAUTION

Damage hazard: Do not weld or solder on any part of the fuel system and servo oil system.
Damage to the system can occur.

2.2.4

Personal safety and protection equipment

Always use the below given personal protection equipment during repair and maintenance work
on the engine.

•

Safety helmet.

•

Ear protection.

X72-B

AA00-0000-00AAA-012A-A

Operation Manual

Safety precautions and safety guidelines

Winterthur Gas & Diesel Ltd.

- 47 -

Issue 003 2021-12

«
...
45
46
47
48
49
...
»

Содержание X72-B















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды