manualshive.com logo in svg

WinGD X72-B, Руководство по эксплуатации

Поделиться
Скачать
WinGD X72-B Скачать руководство пользователя страница 398

Tab 10-31  Fuel leakage flow from fuel rail items is too high (engine with ICU)

Indication

Possible cause

Procedure

LS3446-nnA

An injection control unit (ICU) or a
pipe or a connecting pipe (if appli-
cable) is defective

•

Find the cause and repair the defective item,
refer to section 

[section not applicable for

this engine]

.

Tab 10-32  Fuel pressure in the fuel rail is too high (for X35/-B or X40/-B engine)

Indication

Possible cause

Procedure

PT3461-62C

Control signal is missing or wrong

•

Find out the applicable flow control valve.

•

Related to the necessary engine power
close the 3/2-way valve 10-8752_E0_3-4 in
the HP fuel pipe of the related fuel pump.

Flow control valve of a fuel pump is
defective

•

Clean or replace the defective flow control
valve.

Tab 10-33  Fuel pressure in the fuel rail is too low (for X35/-B or X40/-B engine)

Indication

Possible cause

Procedure

PT3461-62C

Control signal is missing or wrong

•

Find out the applicable flow control valve.

•

Disconnect the cable of the applicable flow
control valve (The related fuel pump sup-
plies the maximum fuel quantity. The pres-
sure control valve of the fuel rail or the other
fuel pump then controls the fuel pressure).

Flow control valve of a fuel pump is
defective

•

Clean or replace the defective flow control
valve.

A fuel pump is defective

•

Replace the defective fuel pump.

X72-B

AA00-0000-00AAA-410C-A

Operation Manual

Malfunctions of systems and components

Winterthur Gas & Diesel Ltd.

- 398 -

Issue 003  2021-12

Содержание X72-B















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды