WinGD X72-B страница 298 Скачать руководство пользователя | Manualshive

Страница: 298 / 526

background image

6.7.5

WiCE - Manual Control Panel (MCP) replacement

6.7.5.1

Manual Control Panel (MCP) replacement

NOTE:

The Manual Control Panel (MCP) local and Manual Control Panel (MCP) ECR are fully
interchangeable items. New control panels are supplied with pre-installed application
software.

1

Stop the engine, if required.

2

Open the cover of the E26 control box (002,

), to get control on the rear of the

Manual Control Panel (MCP) (001).

3

Disconnect the C1 plug (003,

) from the Manual Control Panel (MCP).

4

Disconnect the C2 plug (002) from the Manual Control Panel (MCP).

5

If applicable disconnect the C3 plug (004) from the Manual Control Panel (MCP).

6

Loosen the screws (001) from the bracket.

NOTE:

Make sure the display unit does not fall.

7

Remove the Manual Control Panel (MCP) from the bracket.

8

Attach a “Faulty” label to the control module.

NOTE:

If the part need to be returned to WinGD service station, fill the return sheet
attached to the box of the spare control module.

9

Attach new MCP, either to E26 or in the ECR.

10

Install the bracets on the new Manual Control Panel (MCP).

11

Tighten the brackets with the screws (001).

12

Connect the C2 plug (002) to the Manual Control Panel (MCP).

13

Connect the C1 plug (003) to the Manual Control Panel (MCP).

14

If applicable, connect the C3 plug (004) to the Manual Control Panel (MCP).

15

Close the cover of the control box E26 or ECR.

16

Do a function test to make sure that the Manual Control Panel (MCP) operates correctly.

•

Operating application is functional.

•

CAN bus connection is operational.

17

Make sure to operate the engine as quickly as possible (latest at save ship position) with
the new Manual Control Panel (MCP).

X72-B

AA00-0000-00AAA-200F-A

Operation Manual

WiCE - Manual Control Panel (MCP) replacement

Winterthur Gas & Diesel Ltd.

- 298 -

Issue 003 2021-12

«
...
296
297
298
299
300
...
»

Содержание X72-B















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X72-B

Бренд: Quick Fuel Technology Страницы: 5

Бренд: Beta Marine Страницы: 88

Бренд: Lenze Страницы: 20

EM-PMI540-T1500

Бренд: Danfoss Страницы: 76

AUTOMATE MT01-2101-069002

Бренд: rollease acmeda Страницы: 30

RolloTube S-line Sun DuoFern

Бренд: RADEMACHER Страницы: 2

Бренд: WÜRGES Страницы: 24

Бренд: Hacker Страницы: 2

Бренд: Hacker Страницы: 7

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

Бренд: Haas Страницы: 7

Бренд: Yanmar Страницы: 214

Бренд: Stober Страницы: 34

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: Baumuller Страницы: 24

Бренд: Honda Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды