Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 79 / 152

background image

TH210

Programmer’s Guide

75

Bit

Off/On Hex

Decimal

Status for ASB

4

Off

00

0

Undefined

5

Off

00

0

Undefined

6

Off

00

0

Undefined

7

On

00

0

Undefined

Exceptions

If n = 0, ASB is disabled

Related information

When Automatic Status Back (ASB) is enabled using this command, the status transmitted by other
commands and the ASB status are differentiated according to the information found in
Recognizing Data from the printer, (in the Real Time Commands section in this chapter). The status
bytes to be transmitted are described in the following four tables.

Byte 1 = printer information
Byte 2 = error information
Byte 3 = paper sensor information
Byte 4 = paper sensor information

First byte (Printer Information)

Bit

Off/On Hex

Decimal

Status for ASB

0

Off

00

0

Not used. Fixed to off.

1

Off

00

0

Not used. Fixed to off.

2

Off

00

0

One or both cash drawers open.

On

04

4

Both cash drawers closed.

3

Off

00

0

Not busy at the RS232C interface.

On

08

8

Printer is busy at the RS232C interface.

4

On

10

16

Not used. Fixed to on.

5

Off

00

0

Receipt cover closed.

On

20

32

Receipt cover open.

6

Off

00

0

Paper feed button is not pressed.

On

40

64

Paper feed button is pressed.

7

Off

00

0

Not used. Fixed to off.

Second byte (error Information)

Bit

Off/On Hex

Decimal

Status for ASB

0

–

–

–

Undefined

1

–

–

–

Undefined

2

Off

00

0

No mechanical error

On

04

4

Mechanical error occurred

3

Off

00

0

No knife error.

On

08

8

Knife error occurred.

4

Off

00

0

Not used. Fixed to off.

5

Off

00

0

No unrecoverable error.

On

20

32

Unrecoverable error occurred.

6

Off

00

0

No recoverable error.

«
...
77
78
79
80
81
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

IMAGERUNNER ADVANCE C5051

Бренд: Canon Страницы: 72

iPF710 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 92

iPF8000S - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 8

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 48

Two-Knife Booklet Trimmer-A1

Бренд: Canon Страницы: 32

Perfect Binder-C1

Бренд: Oce Страницы: 82

IMAGERUNNER 7095 PRINTER

Бренд: Canon Страницы: 615

imageRUNNER C3125i

Бренд: Canon Страницы: 816

SCX-4300 - SCX 4300 B/W Laser

Бренд: Samsung Страницы: 97

SCX 4828FN - Laser Multi-Function Printer

Бренд: Samsung Страницы: 151

SCX 4725FN - B/W Laser - All-in-One

Бренд: Samsung Страницы: 120

SCX 4500 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 97

SCX 4200 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 95

SCX 4500 - B/W Laser - All-in-One

Бренд: Samsung Страницы: 172

ProXpress M337x

Бренд: Samsung Страницы: 56

PROXPRESS M332 SERIES

Бренд: Samsung Страницы: 50

ML-2240 - 23 Ppm Mono Laser Printer

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды