Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 60 / 152

background image

TH210

Programmer’s Guide

56

Download font

ASCII

GS 0xF0 0x80 followed by file

Hexadecimal

1D F0 80

Decimal

29 240 128

This command is the sequence introducer for downloading existing files.
The downloaded font is always stored in the permanent font area of flash. If there is not enough
memory in the permanent font area to store the file the printer returns NACK.
When the file is downloaded the printer returns ACK.
If the file contents are incorrect the printer returns NACK. File format to be described in appendix.
So the full sequence for downloading files as font ID CB would be:

1D F0 01 CB

1D F0 80

followed by map file shftjis.chr

1D F0 02 02

1B 20 n

for horizontal character spacing 1B 33 n

1B 33 n

for vertical character spacing

1D F0 80

followed by character definition file shftj24.chr

Graphics

These commands are used to enter and print graphics data and are described in order of their
hexadecimal codes, unless otherwise noted.
These commands describe operation for 80mm paper.

Download BMP logo

ASCII

ESC (+*.BMP file)

Hexadecimal

1B (+*.BMP file)

Decimal

27 66 77(+*.BMP file)

Value

Maximum width = 576
Maximum height = 512

Enters a downloaded BMP logo into RAM or flash.
The downloaded BMP logo can be printed by using the print downloaded bit image (1D 2F m)
command.
To downloaded BMP file to save it as a logo, send the hexadecimal code 1B followed by the whole
BMP file.
The printer decodes the BMP file header and will save the image data after checking important
parameters, such as:



Width



Height



Number of colors (only monochrome images are accepted)

BMPs and bit images continue to be definable only for the receipt station. However, there is no
longer an automatic erasure whenever the user downloads a character set (as happened
previously) as well as in the case where the current logo was never set > 0, (the automatic erasure
if user flash memory had filled up with inactive logo 0 definitions upon next power cycle).

«
...
58
59
60
61
62
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

Бренд: Canon Страницы: 358

Бренд: Oki Страницы: 2

Бренд: Acadian Robotics Страницы: 2

Бренд: QMS Страницы: 26

RS/6000 44P Series 270

Бренд: IBM Страницы: 216

VariQuest Perfecta 2400STP

Бренд: Varitronics Страницы: 227

Бренд: Xerox Страницы: 9

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 150

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 6

Бренд: Xerox Страницы: 2

DocuPrint N2125

Бренд: Xerox Страницы: 246

DocuPrint N2025

Бренд: Xerox Страницы: 378

DocuPrint N2025

Бренд: Xerox Страницы: 176

DocuPrint C3290 FS

Бренд: Xerox Страницы: 240

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды