Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 78 / 152

background image

TH210

Programmer’s Guide

74

Real time commands disabled

ASCII
Hexadecimal
Decimal

US z n
1F 7A n
31 122 n

Value of

n

:

0 = enable
1 = disable

This command is used to disable real time commands. They are disabled prior to sending graphic
or other data to the printer that may contain embedded real time commands.
The command is a batch command and processed in the order received.

Automatic Status Back

Enable/disable Automatic Status Back (ASB)

ASCII
Hexadecimal
Decimal

GS a n
1D 61 n
29 97 n

Range of

n

:

0 - 255

Default:

0 (ASB disabled)

Enables or disables automatic status back (ASB) and specifies the status items. This command is a
batch mode command; that is, it is processed after all prior data in the input buffer has been
processed. There may be a time lag between the printer receiving this command and changing the
ASB response, depending on the receive buffer contents.
If any of the status items listed are selected, ASB is enabled and the printer automatically transmits
4 status bytes whenever the selected status changes. If no status is selected, ASB is disabled. All
four status bytes are transmitted without checking DSR
If the error status is enabled, a change in the following conditions will trigger the ASB:



Cash Drawer



Receipt Cover



Knife Error



Out-of-Range Printhead Temperature



Out-of-Range Voltage



Paper Exhaust Status

The bits of n are defined in the table.

Bit

Off/On Hex

Decimal

Status for ASB

0

Off

00

0

Cash drawer status disabled.

On

01

1

Cash drawer status enabled.

1

Off

00

0

RS-232C Busy status disabled.

On

02

2

RS-232C Busy status enabled.

2

Off

00

0

Error status disabled.

On

04

4

Error status enabled.

3

Off

00

0

Receipt paper roll status disabled.

On

08

8

Receipt paper roll status enabled.

«
...
76
77
78
79
80
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

Бренд: Canon Страницы: 86

Бренд: Canon Страницы: 20

Бренд: WaxJet Страницы: 131

Бренд: Tektronix Страницы: 286

Бренд: GCC Technologies Страницы: 97

Бренд: Konica Minolta Страницы: 15

Бренд: Tally Dascom Страницы: 2

Бренд: iDPRT Страницы: 74

Бренд: Memjet Страницы: 181

ESP 3200 Series

Бренд: Kodak Страницы: 90

Бренд: Evolis Страницы: 45

DYMO LABELWRITER 450 TURBO H-1265

Бренд: U-Line Страницы: 9

Бренд: SATO Страницы: 255

imageRUNNER ADVANCE DX C5870i

Бренд: Canon Страницы: 100

imageRUNNER ADVANCE C356iF

Бренд: Canon Страницы: 96

imageRUNNER ADVANCE C350 series

Бренд: Canon Страницы: 1173

imageRUNNER ADVANCE DX 6870i

Бренд: Canon Страницы: 100

imageRUNNER ADVANCE 715iFZ III

Бренд: Canon Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды