Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 13 / 152

background image

TH210

Programmer’s Guide

9

Enable or disable data scope mode

The data scope mode test prints a hexadecimal dump of all data sent to the printer: “1” prints as
hexadecimal 31, “A” as hexadecimal 41 and so on. This helps troubleshoot communication
problems and runs during a normal application (after being enabled through printer configuration).
Note: Data scope mode is usually considered a level 1 diagnostic test.
Data scope mode is enabled and disabled by selecting the “Diagnostics Modes” sub-menu of the
configuration menu. Press the paper feed button as instructed on the “Diagnostics Modes Menu”
to enable or disable the data scope mode test.



Off, normal mode (Data scope mode disabled)



Data scope mode with or without graphics (enabled)

Note: Press the paper feed button for at least one second to validate the selection.

To run the data scope mode:

1.

After you have enabled the data scope mode, exit the configuration menu.

2.

Run a transaction from the host computer.

All commands and data sent from the host computer will be printed as hexadecimal characters as
shown in the illustration.

To exit the data scope mode:

1.

Enter the configuration menu again.

2.

Disable the data scope mode.

3.

Exit the configuration menu.

The printer is on-line and can communicate normally with the host computer.

Enabling the data scope mode

Refer to the section “Configuring the printer”.

Enable or disable receipt test mode

The receipt test mode verifies proper receipt printing. Receipt test is enabled and disabled by
selecting the “Diagnostics Modes” sub-menu of the configuration menu. See “Configuring the
printer”, for instructions on how to enter the configuration menu.

To run the receipt test mode:

1.

Enable the receipt test mode in the configuration menu.

2.

Exit the configuration menu.

«
...
11
12
13
14
15
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

Бренд: Samsung Страницы: 347

SCX 6555N - MultiXpress Mono Multifunction

Бренд: Samsung Страницы: 180

SCX-4300 - SCX 4300 B/W Laser

Бренд: Samsung Страницы: 18

SCX-4521FG - B/W Laser - All-in-One

Бренд: Samsung Страницы: 215

SCX 6320F - B/W Laser - All-in-One

Бренд: Samsung Страницы: 332

SCX 4828FN - Laser Multi-Function Printer

Бренд: Samsung Страницы: 248

SCX 4725FN - B/W Laser - All-in-One

Бренд: Samsung Страницы: 253

ML 2851ND - B/W Laser Printer

Бренд: Samsung Страницы: 179

ML 2510 - B/W Laser Printer

Бренд: Samsung Страницы: 84

ML 1740 - B/W Laser Printer

Бренд: Samsung Страницы: 152

ML 1630 - B/W Laser Printer

Бренд: Samsung Страницы: 142

ML 1630 - B/W Laser Printer

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 384

Lazett Combo SCX-4216F

Бренд: Samsung Страницы: 135

Бренд: Samsung Страницы: 414

SCX 6555N - MultiXpress Mono Multifunction

Бренд: Samsung Страницы: 112

scx-4100 series

Бренд: Samsung Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды