Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 77 / 152

background image

TH210

Programmer’s Guide

73

n

= 2

Recovers from an error after clearing the receive and print buffers. Print settings that are normally
preserved from line to line, such as character height and width, are still preserved with this
command. This sequence is ignored except when the printer is busy due to an error condition.
The same error recovery possibilities exist as for

n

= 1.

Exceptions

The command is ignored if

n

is out of range.

An application using DLE (0x10) sequence must send ENQ within 100 milliseconds of DLE or the
printer will misinterpret the DLE and execute a clear printer command. Avoid this possibility by
using the ID 03

n

sequence, that is handled exactly the same as 10 05

n

.

Real time printer status transmission

ASCII
Hexadecimal
Decimal

GS ENQ
1D 05
29 5

Transmits one byte status of the printer in real time.

Value of byte:

Bit

Off/On Hex

Decimal

Function

0

Off

00

0

Paper adequate.

On

01

1

Paper low (if paper low sensor enabled).

1

Off

00

0

Paper adequate.

On

02

2

Paper low (if paper low sensor enabled).

2

Off

00

0

Cover closed.

On

04

4

Cover open.

3

Off

00

0

Not busy at the RS-232C interface.

On

08

8

Printer is busy at the RS-232C interface.

4

Off

00

0

One or both cash drawers open.

On

10

16

Both cash drawers closed.

5

Off

00

0

Fixed to off.

6

Off

00

0

No error condition.

On

40

64

Error condition exists in the printer.

7

On

80

128

Fixed to on.

* Errors include cover open, paper out, black mark error, cutter error, thermistor error, high or low
voltage error, where a thermistor error is unrecoverable, and a high or low voltage error
automatically recover.

Exceptions

Unlike the A793, that had a dedicated connector and resultant dedicated status reporting for each
cash drawer, the TH210 has a single connector that shares data reporting from either cash drawer.
When either cash drawer is open, an open status is reported by the printer.

«
...
75
76
77
78
79
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 341

Бренд: Samsung Страницы: 8

CLX2160N - Color Laser - All-in-One

Бренд: Samsung Страницы: 118

CLX 3160FN - Color Laser - All-in-One

Бренд: Samsung Страницы: 142

CLP-770ND - Color Laser Printer

Бренд: Samsung Страницы: 2

CLP 610ND - Color Laser Printer

Бренд: Samsung Страницы: 114

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 15

CLP 600N - Color Laser Printer

Бренд: Samsung Страницы: 227

CLP 600N - Color Laser Printer

Бренд: Samsung Страницы: 118

CLP 300N - Network-ready Color Laser Printer

Бренд: Samsung Страницы: 94

CJX-2000FW Series

Бренд: Samsung Страницы: 2

4116 - SCX B/W Laser

Бренд: Samsung Страницы: 205

3561ND - B/W Laser Printer

Бренд: Samsung Страницы: 252

3561ND - B/W Laser Printer

Бренд: Samsung Страницы: 127

Бренд: Samsung Страницы: 314

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды