Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 12 / 152

background image

TH210

Programmer’s Guide

8

Communication interface settings

To change the communication interface settings, enter the configuration menu, select “Set
Communication Interface” from the main menu.

Caution:

Be extremely careful changing any of the printer settings to avoid inadvertently changing

other settings that might affect the performance of the printer.
Press the paper feed button as instructed on the configuration menu to select the settings you
want to change.



Baud rate

115200 baud
57600 baud
38400 baud
19200 baud
9600 baud
4800 baud
2400 baud
1200 baud



Parity

No Parity
Even Parity
Odd Parity



Flow control methd

Software (XON/XOFF)
Hardware (DTR/DSR)



Data reception errors

Ignore errors
Print “?”



Alternate DTR/DSR

Enabled
Disabled



USB Driver

Printer Cass
Comm Class



USB NAK

Reject Packets When Error
Accept Packets When Error

Note: Press the paper feed button for at least one second to validate the selection.

Setting the RS-232C Serial interface settings

Refer to the section “Configuring the printer”.

Diagnostics modes

To change the the diagnostic modes enter the configuration menu, select “Set Diagnostics Modes”
from the main menu and select one of the following modes:



Normal: normal operating mode of the printer.



Datascope: the receipt printer prints incoming commands and data in hexadecimal

format to help troubleshoot communication problems. There are DataScope modes
for both with and without graphics.



Receipt test: the receipt printer prints all code pages to verify proper printing of the

receipt.

Caution: Be extremely careful changing any of the printer settings to avoid inadvertently changing
other settings that might affect the performance of the printer.
Refer to the section “Configuring the printer,” for instructions on how to enter the configuration
menu.

«
...
10
11
12
13
14
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

Бренд: Canon Страницы: 37

Бренд: Xiamen Hanin Electronic Technology Страницы: 62

mC-Print3 MCP31LB

Бренд: Star Страницы: 12

Бренд: Olivetti Страницы: 24

ThermalTronix TT-1260S-UTCM

Бренд: Intellisystem Страницы: 18

Бренд: Pantum Страницы: 164

Бренд: Star Страницы: 88

Бренд: idp Страницы: 88

WorkCentre 6400XF

Бренд: Xerox Страницы: 24

accuriopress c6085

Бренд: Konica Minolta Страницы: 81

Бренд: Xerox Страницы: 284

Бренд: Parkside Страницы: 77

ECOSYS FS-C2526MFP

Бренд: Kyocera Страницы: 36

Бренд: Xante Страницы: 3

SPECTRUM Z M510

Бренд: Z Corporation Страницы: 7

Бренд: Savin Страницы: 90

WorkCentre 7232

Бренд: Xerox Страницы: 96

imageRUNNER ADVANCE C255i

Бренд: Canon Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды