Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 43 / 152

background image

TH210

Programmer’s Guide

39

Text characteristics commands

These commands control what the printed information looks like, selection of character sets,
definition of custom-defined characters, and setting of margins. The commands are described in
order of their hexadecimal codes.
The commands describe operation for 80mm paper.

Select double-wide characters

ASCII

DC2

Hexadecimal

12

Decimal

18

Prints double-wide characters. The printer is reset to single-wide mode after a line has been
printed or the clear printer
(0x10) command is received. Double-wide characters may be used in the same line with single-
wide characters.

Exceptions

Double-wide characters may not be used in the same line with single or double-density graphics.

Related information

This is ignored in LEGACY emulation.

Select single-wide characters

ASCII

DC3

Hexadecimal

13

Decimal

19

Prints single-wide characters. Single-wide characters may be used in the same line with double-
wide characters.

Exceptions

Single-wide characters may not be used in the same line with single or double-density graphics.

Related information

This is ignored in LEGACY emulation.

Select 90 degree counter-clockwise rotated print

ASCII

ESC DC2

Hexadecimal

1B 12

Decimal

27 18

Rotates characters 90 degrees counter-clockwise. The command remains in effect until the printer
is reset or until a clear printer (0x10), select or cancel upside down print (1b 7b) or cancel rotated
print (1b 56) command is received.

Exceptions

This command is valid only at the beginning of a line.

«
...
41
42
43
44
45
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

Бренд: QMS Страницы: 122

Бренд: QMS Страницы: 306

Бренд: Panasonic Страницы: 240

Бренд: DataCard Страницы: 130

Бренд: Xerox Страницы: 288

Бренд: Creality Страницы: 24

FELIX Pro 3 Touch

Бренд: Felix printers Страницы: 29

Бренд: Ricoh Страницы: 236

Бренд: Novexx Solutions Страницы: 6

ECOSYS FS-C2126MFP

Бренд: Kyocera Страницы: 206

Бренд: MIMAKI Страницы: 27

C12C823912 - Net 2 Print Server

Бренд: Epson Страницы: 20

C823622A - Interface Type B Print Server

Бренд: Epson Страницы: 3

C12C800WN (Net 802.11b Wireless Print Server)

Бренд: Epson Страницы: 2

C32C824461 - UB R03 Print Server

Бренд: Epson Страницы: 86

Бренд: Epson Страницы: 279

C823622A - Interface Type B Print Server

Бренд: Epson Страницы: 2

Star futurePRNT TSP100GT

Бренд: Star Micronics Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды