Wincor Nixdorf TH210 Скачать руководство пользователя | Manualshive

Страница: 44 / 152

background image

TH210

Programmer’s Guide

40

Rotated print and non-rotated print characters cannot be used together in the same line.

Related information

See “Summary of rotated printing” in this document.
This is ignored in LEGACY emulation.

Set pitch (column width)

ASCII

ESC SYN

n

Hexadecimal

1B 16

n

Decimal

27 22

n

Value of

n

:

0 = Standard pitch
1 = Compressed pitch

Default of

n

:

0 (Standard pitch)

Selects the character pitch for a print line.

Formulas
The following table provides the print characteristics for both pitches on the receipt station.

Pitch

Columns, 80mm Paper

CPI

Standard

44

15.6

Compressed

56

20.3

Related information

Look in Chapter “Programming the Printer, Character appearance” for a description of both
pitches.
This command and the select print modes command (1B 21

n

) affect pitch selection.

This is ignored in LEGACY emulation and the parameter byte goes into the print buffer.

Set right-side character spacing

ASCII

ESC SP

n

Hexadecimal

1B 20

n

Decimal

27 32

n

Range of

n

:

0 – 32 (decimal)

Default:

0

The units of horizontal and vertical motion are specified by the set horizontal and vertical
minimum motion units (1D 50 …) command. Changes in the horizontal or vertical units do not
affect the current right side character spacing. When the horizontal or vertical motion unit is
changed by the set horizontal and vertical minimum motion units (1D 50 …) command the value
must be in even units and not less than the minimum amount of horizontal movement.
In standard mode the horizontal motion unit is used.
In page mode the horizontal or vertical motion unit differs and depends on the starting position of
the printable area. When the starting printing position is the upper left or lower right of the
printable area (set by select print direction in page mode, 1B 54 n) the horizontal motion unit (x) is

«
...
42
43
44
45
46
...
»

Содержание TH210

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для TH210

Бренд: Zeka Страницы: 54

Бренд: DataCard Страницы: 2

Бренд: oliser Страницы: 6

Бренд: Xerox Страницы: 44

Бренд: Oki Страницы: 76

Бренд: Canon Страницы: 36

Бренд: Canon Страницы: 62

WorkCentre 4260S

Бренд: Xerox Страницы: 8

Бренд: Canon Страницы: 738

Бренд: Samsung Страницы: 143

imageRUNNER 6570

Бренд: Canon Страницы: 274

Бренд: Xerox Страницы: 14

Бренд: Xerox Страницы: 2

Бренд: Ricoh Страницы: 781

Бренд: Oki Страницы: 4

Бренд: Olivetti Страницы: 22

Бренд: BIO RAD Страницы: 61

Бренд: Lexmark Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды