Wincor Nixdorf TH210 Скачать руководство пользователя

Страница: 56 / 152

TH210

Programmer’s Guide

In A793 emulation, the command is unrecognized and the parameter byte is put into the print
buffer.

Set smoothing

ASCII

GS b

Hexadecimal

1D 62

Decimal

29 98

Value of

0 = smoothing off
1 = smoothing on

Default:

0 (Off)

Turns smoothing mode on or off for the quadruple or larger sizes of characters.

Select superscript or subscript modes

ASCII

US ENQ

Hexadecimal

1F 05

Decimal

31 05

Value of

0 = Normal character size
1 = Select subscript size
2 = Select superscript size

Default:

0 (Normal size)

Turns superscript or subscript modes on or off. This attribute may be combined with other
characters size settings commands (12, 13, 1B 21

, 1D 21

,…)

Exceptions

This command is ignored if

is out of the specified range.

Related information

In A793 emulation, this command is unrecognized and the parameter byte is put into the print
buffer.

Select active user-defined character set

ASCII

i n

Hexadecimal

1F 69

Decimal

31 105

n = 0 -127
Set high order bit of

to configure user-defined character set number as the default. To configure

the printer to print from the user-defined character set at power, send 1F 03 0F 01 and reset the
printer. Information will print on the first diagnostic page.

Содержание TH210

























































































































































Результаты поиска

Содержание TH210

Отзывы:

Похожие инструкции для TH210

Бренды по названию

Популярные бренды

Wincor Nixdorf TH210, Руководство программиста

Результаты поиска

Содержание TH210

Отзывы:

Похожие инструкции для TH210

Бренды по названию

Популярные бренды