White Mountain Hearth DVD32FP3 Series Скачать руководство пользователя

Страница: 41 / 52

Page 41

17333-15-0806

1. Remove glass door and place away from the ﬁreplace.

2. Turn on gas shut off valve. Follow ignition procedure.

3. If burner does not light after spark sequence has ended, use an

insulated jumper wire (see page 40) between terminal locations

12 and 13 for fast reset function.

4. Interrupt power for 5 seconds. The green indicator light will

blink 4 times repetitively. Then retry for ignition.

5. Allow time for any raw gas to dissipate and repeat steps 3 and

4 until ignition is achieved.

6. Turn burner off and install glass door frame assembly.

7. Test ignition of burner with glass door in place.

FOR YOUR SAFETY READ BEFORE LIGHTING

Warning: if you do not follow these instructions exactly, a ﬁre or explosion may result causing property damage,

personal injury, or loss of life.

A. BEFORE LIGHTING smell all around the heater area for gas.

Be sure to smell next to the ﬂoor because some gas is heavier

than air and will settle on the ﬂoor.

WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any ﬁreplace.

• Do not touch any electric switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone.

Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the Fire

Department.

B. Use only the wall switch or remote control switch to turn the

gas control on/off. Any attempted repairs or adjustments should

be performed by a qualiﬁed service technician. Applying force

or any attempted repair may result in a ﬁre or explosion.

C. Do not use this ﬁreplace if any part has been under water.

Immediately call a qualiﬁed service technician to inspect the

heater and to replace any part of the control system and any gas

control which has been under water.

1. STOP! Read the safety information above.

2. Set the thermostat, if used, to the lowest setting.

3. Turn off electric power to the appliance.

4. This appliance is equipped with an ignition device that

automatically lights the burner. Do not try to light the burner

by hand.

OFF

5. Lower louver front assembly.

6. Turn gas line valve to "ON."

7. Wait ﬁve (5) minutes to clear out any gas. Then smell for gas,

including near the ﬂoor. If you do smell gas, STOP! Follow

“A” in the safety information above. If you do not smell gas,

go to the next step.

8. Close bottom louver assembly.

9. Turn on all electric power to the appliance.

10. Set thermostat to desired setting (if available).

11. If the appliance will not operate, follow the instructions below

on how to turn off gas to heater, and call your service technician

or gas supplier.

1. STOP! Read the safety information above.

2. Set the thermostat, if used, to the lowest setting.

3. Turn off electric power to the appliance.

4. Open bottom louver assembly.

5. Turn gas line valve to “OFF.”

6. Close bottom louver assembly.

NOTE: UNIT MUST BE PROPERLY GROUNDED FOR ELECTRONIC IGNITION TO FUNCTION.

On initial installation, or after extended periods where the ﬁreplace has not been used, gas lines may require purging.

The installer or qualiﬁed service person may use the following purge procedures to prevent the delays that would be caused by

waiting for the lockout periods between tries for ignition.

PURGE PROCEDURE

INSULATED

JUMPER WIRE

HOW TO TURN OFF GAS TO HEATER

LIGHTING INSTRUCTIONS

DIRECT IGNITION LIGHTING INSTRUCTIONS

INITIAL START UP GAS LINE PURGE

Содержание DVD32FP3 Series





















































Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVD32FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды