White Mountain Hearth DVD32FP3 Series Скачать руководство пользователя

Страница: 29 / 52

Page 29

17333-15-0806

Follow correct option according to venting method.

Connecting Directly to Fireplace

If the air inlet and ﬂue outlet tubes are to be connected directly to

the unit (no rigid venting system is being used), then the gasket

provided must be used to seal the 4” (102mm) ﬂue outlet tube.

Peel the paper off the self-adhesive gasket and then wrap it around

the end of the tube (if tube was cut, it is recommended to use cut

end) as shown in Figure 4. Pull the gasket tight at all times while

wrapping it around tube. The gasket ends should align, to form a

complete seal. The overlapped section should NOT come in con-

tact with the seam in the tube. Apply high temperature sealant to

the opposite end of the tube (on the inside of the tube). The end

with the gasket will attach to the back of the unit. Continue with

Step 13.

Connecting to Rigid Vent System

If the air inlet and ﬂue outlet tubes are to be connected to a rigid

venting system (and not directly to the back of the unit), then

not

use the gasket provided. High temperature sealant should be

applied to the outside of the 4” diameter (102mm) ﬂue outlet tube

(if tube was cut, it is recommended to use cut end) and to the in-

side of the tube on the end that connects to the vent cap. Continue

with step 13.

PARTS LIST

INDEX

NUMBER

PART

NUMBER

DESCRIPTION

DV769

Vent Cap Assembly

19193

Outside Mounting Plate

19194

Air Inlet Tube

DV524

Flue Outlet Tube

19196

Firestop/Thimble Assembly

20527

Gasket

DVVK-4RE VENT KIT INSTALLATION INSTRUCTIONS (continued)

Содержание DVD32FP3 Series





















































Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVD32FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды