White Mountain Hearth DVD32FP3 Series Скачать руководство пользователя страница 23

Страница: 23 / 52

Page 23

17333-15-0806

nstalling Vent Components (Figure 36)

Begin the vent system installation by installing the ﬁrst Simpson

Duravent component, 90° elbow to the starting collars or straight

pipe on the top of the appliance, then the straight pipe length and

then horizontal or vertical termination kit.

NOTE: All outer connection joints must be sealed with aluminum

tape, screws or silicone sealant rated above 300°F/149°C. The

inner ﬂue joints do not require any sealant.

Simpson Duravent vent system components lock into place by

sliding the concentric pipe section with four (4) equally spaced

interior beads onto the appliance collar or previously installed

component end with four (4) equally spaced indented sections.

When the internal beads of each starting outer pipe line up, rotate

pipe section clockwise 90° (approximately 3 inches). The vent pipe

is now locked together.
Continue adding components per the pre-planned vent system

conﬁguration. Be certain that each succeeding vent component

is securely ﬁtted and locked into the preceding component in the

vent system.

Figure 36

WALL THIMBLE

(MAXIMUM OF

THREE 90 ELBOWS)

(MAXIMUM OF

TWO 90 ELBOWS)

Special Venting Components

Simpson Dura-Vent

Can be purchased from Simpson Duravent or from Empire

Comfort Systems, Inc.

Part Number

Description

SD-908

6" Pipe Length

SD-907

9" Pipe Length

SD-906

12" Pipe Length

SD-904

24" Pipe Length

SD-903

36" Pipe Length

SD-902

48" Pipe Length

SD-911

Adjustable Pipe Length 11 - 14 5/8"

SD-985

Horizontal Square Termination Cap

SD-950

Vinyl Siding Standoff

SD-945

45° Elbow

SD-990

90° Elbow

SD-947

Wall Firestop

SD-963

Ceiling Firestop

SD-942

Wall Thimble

SD-943

Roof Flashing - 0/12 to 6/12 Roof Pitch

SD-953

Storm Collar

SD-991

High Wind Vertical Top

SD-981

36" Snorkel

SD-982

14" Firestop Snorkel

SD-988

Wall Strap

Special DV Vent Kits - Simpson Duravent and Empire Comfort Systems, Inc.

Can be purchased from Empire Comfort Systems, Inc.

DVVK-4V

Direct-Vent Fireplace Vent Kit - Vertical, Includes SD-991, SD-

953, and SD-943

DVVK-4T

Direct-Vent Fireplace Vent Kit for Top Vent, Thru-the-wall, 8 to

11 inch wall thickness, Includes SD-911, SD-985, SD-990 and

SD-942

DVVK-4R

Direct-Vent Fireplace Vent Kit for Rear Vent, 5 to 7 inch wall

thickness, (standard thru-the-wall venting) Includes SD-908, SD-

985 and SD-942

DVVK-4TS Direct-Vent Fireplace Vent Kit for Top Vent, Thru-the-wall, 5 to

7 inch wall thickness, Includes SD-908, SD-985, SD-990 and

SD-942

VENT SYSTEM IDENTIFICATION

Содержание DVD32FP3 Series





















































Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Бренды по названию

Популярные бренды

White Mountain Hearth DVD32FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Бренды по названию

Популярные бренды