White Mountain Hearth DVD32FP3 Series страница 12 Скачать руководство пользователя

Страница: 12 / 52

Page 12

17333-15-0806

Note

: For ﬁnishing to top of ﬁreplace, refer to Figure 12.

DVD32

DVD36

DVD42

DVD48

"A"

35 3/4"

(908mm)

35 3/4"

(908mm)

37 3/4"

(959mm)

37 3/4"

(959mm)

"B"

34 3/8"

(873mm)

37 3/8"

(949mm)

43 3/8"

(1102mm)

49 3/8"

(1254mm)

"C"

16 3/8"

(416mm)

16 3/8"

(416mm)

16 3/8"

(416mm)

16 3/8"

(416mm)

Figure 11

Attention:

Add 3-3/4" to “A” dimensions when using a ﬂush

mantel base.

Attention:

If a base or mantel is not used and the appliance is

installed directly on carpeting, tile or other combustible material

other than wood ﬂooring, it shall be installed on a metal or wood

panel extending the full width and depth of the appliance. The

vertical dimension in Figure 11 must be adjusted when a metal or

wood panel is placed beneath the appliance.

Finishing (Figures 12 and 13)

Finish the walls with the material of your choice. Figure 3 on

page 8 shows the minimum vertical and corresponding maximum

horizontal dimensions of mantels or other combustible projections

above the top front edge of the ﬁreplace.

Only non-combustible materials may be used to cover the black

ﬁreplace front.

Warning: When ﬁnishing the ﬁreplace never obstruct

or modify the air inlet/outlet louvers in any manner.

Provide adequate clearances around air openings into the

combustion chamber.

Caution:

If the joints between the ﬁnished wall and the ﬁreplace

surround (top and sides) are sealed, a 300°F minimum sealant

material must be used. These joints are not required to be sealed.

Only non-combustible material (using 300°F minimum adhesive if

needed), can be applied as facing to the ﬁreplace surround.

Flush Mount Mantel Installation (Figure 10)

The ﬁreplace must extend 3/4" beyond ﬁnished wall surface when

using a ﬂush mount mantel. Refer to Figure 10 to locate nailing

ﬂanges on ﬁreplace sides. Mark and drill two (2) 1/8" holes into

ﬁreplace side to mount each nailing ﬂange. Use eight (8) 1/2"

hex-head screws supplied in hardware package to attach nailing

ﬂanges to ﬁreplace sides.

Figure 10

Attention:

When ﬁreplace is installed in optional full cabinet mantel

or corner mantel the (4) four nailing ﬂanges shown in Figure 10 will

not be installed on the side of outer casing. The ﬁreplace will be

attached to the full cabinet mantel or corner mantel with the (2) two

nailing ﬂanges located on the top of the outer casing assembly.

Framing (Figure 11)

Fireplace framing can be built before or after the ﬁreplace is set in

place. Framing should be positioned to accommodate wall covering

and ﬁreplace facing material. The ﬁreplace framing should be

constructed of 2 x 4 lumber or heavier. The framing headers may

rest on the ﬁreplace standoffs. Refer to Figure 11 for minimum

framing dimensions.

CAUTION: MEASURE FIREPLACE DIMENSIONS AND

VERIFY FRAMING METHODS, AND WALL COVERING

DETAILS BEFORE FRAMING CONSTRUCTION

BEGINS.

Framing dimension "A" includes a three inch clearance for

standoffs on ﬁrebox. After installing ﬁrebox into framing,

the ﬁnished wall surface must cover the three inch opening

above the ﬁrebox.

NAIL OR OTHER SUITABLE FASTENER

INSTALLATION (continued)

Содержание DVD32FP3 Series





















































Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVD32FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды