White Mountain Hearth DVD32FP3 Series Скачать руководство пользователя

Страница: 33 / 52

Page 33

17333-15-0806

Before you begin: if you are installing logs into the DVD32 or

DVD36 model then this ﬁreplace is supplied with a set of ﬁve

ceramic ﬁber logs. Do not handle these logs with your bare hands!

Always wear gloves to prevent skin irritation from ceramic ﬁbers.

After handling logs, wash your hands gently with soap and water

to remove any traces of ﬁbers.
The positioning of the logs is critical to the safe and clean operation

of this ﬁreplace. Sooting and other problems may result if the logs

are not properly and ﬁrmly positioned in the ﬁreplace. Please refer

Figure 50

and

Figure 51

and corresponding WARNING when

completing following log placement instructions.
1. Remove top louver, grasp louver, lift and pull forward.

2. Lower bottom louver, lift and hinge forward.

3. Release two glass frame spring clamps at bottom of ﬁrebox.

4. Remove glass frame assembly.

5. Place front logs (#1 and #2) between front grate ﬂange and

main burner. Align notches on front logs with locator tabs in

base.

6. Place middle log (#3) between front and rear loop of burner.

Note: Do not place log on top of pilot assembly.

7. Place rear log (#4) on rear log shelf. Bottom ﬂange of log must

be placed between the log shelf and burner tube.

8. Place branch (#5) onto (#1) log and ﬂat area on (#3) log. The

bottom of the branch is to be placed behind the grate tang that

is second from the left.

9. Place decorative rock in front of grates and sides of main burner

pan.

ATTENTION

: Do not place decorative rock on logs or burner.

The decorative rock should only be placed on the ﬁreplace

ﬂoor.

EMBER MATERIAL PLACEMENT ON BURNER

10. After all logs are positioned properly, apply Rockwool ember

material to the front burner port area. To apply, carefully

separate the ember material into small amounts no larger than

"dime size" pieces. Fluffed up pieces one layer thick on top

of the burner generally works best, and will provide the best

ember glow. Do not place ember material more than one layer

thick. No more than (1) small packet of ember material (part

no. 15999) evenly placed on the burner, is recommended on

DVD32 and DVD36 models. Using additional ember material

will decrease the amount of ember glow effect. Extra ember

material should be saved for future ember applications as

necessary.

See Figure 51.

11. Replace glass frame onto ﬁrebox.

12. Secure the two glass frame spring clamps at bottom of

ﬁrebox.

13. Align the tabs on top louver brackets with slots in front posts

to secure top louver.

14. Close bottom louver. Lift slightly to engage the end tabs into

the slots in ﬁreplace sides to close louver panel

Figure 50

WARNING: Failure to position the parts in accordance

with this diagram or failure to use only parts speciﬁcally

approved with this appliance may result in property

damage or personal injury.

Attention:

Do not use Figure 50 or Figure 51 to order logs. Refer

to parts list on page 45 and parts view on page 46 to order logs

and/or ember material for your appropriate ﬁreplace model.

Figure 51

EMBER MATERIAL

PLACEMENT

LOG PLACEMENT (5 LOG SET)

Содержание DVD32FP3 Series





















































Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVD32FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды