White Mountain Hearth DVD32FP3 Series Скачать руководство пользователя

Страница: 38 / 52

Page 38

17333-15-0806

1. Stop! Read the safety information above.

2. Set REMOTE/OFF/ON switch to OFF.

3. Turn off all electric power to the appliance (if applicable).

4. Lower bottom louver assembly.

5. Push in gas control knob slightly and turn clockwise

to "OFF."

Note:

Knob cannot be turned from "PILOT" to "OFF" unless

knob is pushed in slightly. Do not force.

6. Wait ten (10) minutes to clear out any gas. Then smell for

gas, including near the ﬂoor. If you then smell gas, STOP!

Follow "B" in the safety information above. If you do not

smell gas, go to the next step.

7. Find pilot - Follow metal

tube from gas control. The pilot is

behind the burner on the right side.

8. Turn gas control knob

counterclockwise

"PILOT."

9. Push in control knob all the way and

hold in. Repeatedly push the piezo ignitor button until the

pilot is lit. Continue to hold the control knob in the for

about one (1) minute after the pilot is lit. Release knob,

and it will pop back up. Pilot should remain lit. If it goes

out, repeat steps 5 through 9.

• If the control knob does not pop up when released,

STOP and IMMEDIATELY call a qualiﬁed

service technician or gas supplier.

• If the pilot will not stay lit after several tries,

turn the gas control knob to "OFF" and call your

service technician or gas supplier.

10. Turn gas control knob counterclockwise

"ON."

11. Close bottom louver assembly.

12. Turn on all electric power to the appliance (if

applicable).

13. Set REMOTE/OFF/ON switch to desired setting.

TO TURN OFF GAS TO FIREPLACE

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ﬁre or explosion may result causing property
damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. Before lighting smell all around the appliance area for gas.

Be sure to smell next to the ﬂoor because some gas is heavier

than air and will settle on the ﬂoor.

What To Do If You Smell Gas

• Do not try to light any appliance.

• Do not touch any electrical switch;

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the ﬁre

department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or

turn by hand, don't try to repair it; call a qualiﬁed service

technician. Force or attempted repair may result in a ﬁre

or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualiﬁed service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

LIGHTING INSTRUCTIONS

1. Set REMOTE/OFF/ON switch to OFF.

2. Turn off all electric power to the appliance if service is to

be performed (if applicable).

3. Lower bottom louver assembly.

4. Push in gas control knob slightly and turn clockwise

to "OFF." Do not force.

5. Close bottom louver assembly.

THERMOCOUPLE

ELECTRODE

PILOT

THERMOPILE

GAS CONTROL KNOB SHOWN

IN "OFF" POSITION

REMOTE

OFF

STANDING PILOT LIGHTING INSTRUCTIONS

Содержание DVD32FP3 Series





















































Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVD32FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды