White Mountain Hearth DVD32FP3 Series Скачать руководство пользователя

Страница: 32 / 52

Page 32

17333-15-0806

Installation of Vertical Inlet Bafﬂe

The vertical inlet bafﬂe is to be used only in a completely vertical

vent installation. The vertical inlet bafﬂe can be used when the

vertical vent rise is between 10 feet and 40 feet. To maintain the

yellow ﬂame in the main burner, purchase Vertical Inlet bafﬂe,

DVF-139 from your Empire Comfort Systems, Inc. distributor

or dealer.
In a vertical vent rise the rear (yellow) ﬂame on the main burner can

be reduced due to the drawing action from the ﬂue exhaust pipe and

the air inlet pipe. A decrease in the height or the appearance of the

yellow ﬂame may occur when the vertical vent rise is between 10

feet and 40 feet. To enhance the yellow ﬂame on the main burner,

the vertical inlet bafﬂe can be attached to the Simpson Dura-Vent,

991, direct vent high wind vertical top.

Please use the following steps to install the vertical inlet

bafﬂe.

1. Place the vertical inlet bafﬂe over the exterior of the air inlet

openings on the Simpson Dura-Vent, 991, direct vent high wind

vertical top.

2. There are three sections of air openings on the exterior of the

air inlet pipe.

To achieve the

maximum

amount of yellow ﬂame the vertical

inlet bafﬂe will cover-up three sections of air openings.

To achieve the

minimum

amount of yellow ﬂame the vertical

inlet bafﬂe will cover-up one section of air openings.

3. Attach vertical inlet bafﬂe to the Simpson Dura-Vent 991,

direct vent high wind vertical top with (2) 3/8" hex-head screws

provided with vertical inlet bafﬂe.

4. Installation of vertical inlet bafﬂe is completed.

Parts List

Description

Part

Number

Quantity

Supplied

Vertical Inlet Bafﬂe

DVF-139

3/8" Hex-Head Screw

R-2656

Reassembly and Resealing Vent Pipe System

Attach vent pipe to inlet and outlet vent adaptor on ﬁreplace in either

the vertical or horizontal position, replace horizontal and vertical

pipe lengths, elbows and horizontal or vertical termination kit.
All vent system components lock into place by sliding the concentric

pipe section with four (4) equally spaced interior beads onto the

appliance collar or previously installed component end with four

(4) equally spaced indented sections. When the internal beads of

each starting outer pipe line up, rotate pipe section clockwise 90°

(approximately 3 inches). The vent pipe is now locked together.
Continue replacing components per the vent system conﬁguration.

Be certain that each succeeding vent component is securely ﬁtted

and locked into the preceding component in the vent system.

Reassembly and Resealing Gas Accumulation Relief System

Glass Frame Assembly and Combustion Chamber

Whenever the glass frame assembly is pivoted open by a delayed

ignition in the main burner, the glass frame assembly gaskets and

combustion chamber must be examined by a qualiﬁed service person

for damage. All damaged gaskets on the glass frame assembly and

combustion chamber must be replaced by a qualiﬁed service person.

If damage occurs to the combustion chamber, it must be replaced

by a qualiﬁed service person. Contact Empire Comfort Systems,

Inc. for replacement parts.

Vertical Through the Roof Applications (Figure 49)

Your Gas Fireplace has been approved for:

a) Vertical installations up to 40 feet in height.

b) Two sets of 45 degree elbow offsets within these vertical

installations. From 0 to a maximum of 8 ft. a vent pipe can be

used between elbows.

c) Wall straps must be used to support offset pipe every 4'.
This application will require that you ﬁrst determine the roof pitch

and use the appropriate venting components.

12.19

Figure 49

VERTICAL TERMINATION (continued)

Содержание DVD32FP3 Series





















































Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVD32FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды