White Mountain Hearth DVD32FP3 Series страница 6 Скачать руководство пользователя

Страница: 6 / 52

Page 6

17333-15-0806

Instructions to Installer

1. Installer must leave instruction manual with owner after

installation.

2. Installer must have owner ﬁll out and mail warranty card supplied

with the ﬁreplace.

3. Installer should show owner how to start and operate the

ﬁreplace.

This direct vent gas ﬁreplace heater is designed to operate with all

combustion air being siphoned from the outside of the building

and all exhaust gases expelled to the outside of the building. The

information contained in this manual pertains to all models and gas

control systems unless otherwise noted.

Warning: This unit is not for use with solid fuels.

Appliance Certiﬁcation

This ﬁreplace is design certiﬁed in accordance with American

National Standard/CSA Standard ANSI Z.21-88/CSA 2.33 and by

Underwriters Laboratories as a Direct Vent Gas Fireplace Heater

and shall be installed according to these instructions.
Consult your local building code agency, prior to installation,

to ensure compliance with local codes-including permits and

inspections.
The ﬁreplace, when installed, must be electrically grounded in

accordance with local codes or, in absence of local codes, with the

National Electric Code ANSI/NFPA 70

or Canadian Electric code,

CSA C22.1, if an external electrical source is utilized.
These models may be installed in a bedroom or bed-sitting room

in the U.S.A. and Canada.

Qualiﬁed Installing Agency

Installation and replacement of gas piping, gas utilization equipment

or accessories and repair and servicing of equipment shall be

performed only by a qualiﬁed agency. The term “qualiﬁed agency”

means any individual, ﬁrm, corporation or company which either in

person or through a representative is engaged in and is responsible

for (a) the installation or replacement of gas piping or (b) the

connection, installation, repair or servicing of equipment, who is

experienced in such work, familiar with all precautions required

and has complied with all the requirements of the authority having

jurisdiction.

State of Massachusetts:

The installation must be made by

a licensed plumber or gas ﬁtter in the Commonwealth of

Massachusetts.

The installation must conform with local codes or, in the absence of

local codes, with the

National Fuel Gas Code ANSI Z223.1/NFPA

54* Natural Gas and Propane Installation Code, or CSA B149.1

in Canada.

*Available from the American National Standards Institute, Inc. 11

West 42nd St., New York, N.Y. 10036.

Warning

: ANY CHANGE TO THIS FIREPLACE OR ITS

CONTROLS CAN BE DANGEROUS.

Improper installation or use of the ﬁreplace can cause serious

injury or death from ﬁre, burns, explosions, or carbon

monoxide poisoning.

Any alteration of the original design, installed other than as

shown in these instructions or use with a type of gas not shown on

the rating plate is the responsibility of the person and company

making the change.
Important

All correspondence should refer to complete Model Number, Serial

Number and type of gas.

High Altitude

When installing this unit at an elevation above 2000 feet (in the

United States) it may be necessary to decrease the input rating by

changing the existing burner oriﬁce to a smaller size. Generally,

input should be reduced 4 percent for each 1000 feet above sea

level. However, if the heating value of the gas has been reduced,

this general rule may not apply. Check with local gas utility for

proper oriﬁce size identiﬁcation.

Canadian High Altitude

Altitude: 0-4500 feet (0-1370 m)
When installing this unit at an elevation above 4500 feet (in Canada),

check with local authorities.
Consult your local gas utility for assistance in determining the

proper oriﬁce for location.

Preparation

This direct vent gas ﬁreplace and its components are tested and safe

when installed in accordance with this Installation Manual. Report

to your dealer any parts damaged in shipment, speciﬁcally check

glass condition. Do not install unit with damaged, incomplete, or

substitute parts. Read all instructions before starting installation

and follow these instructions carefully during installation to insure

maximum beneﬁt and safety. Failure to follow them will void your

warranty and may present a ﬁre hazard.
The warranty will be voided by, and the warranter disclaims any

responsibility for the following actions:

• Installation of any damaged fireplace or vent system

component.

• Modiﬁcation of the ﬁreplace or direct vent system.

• Installation other than as instructed by Empire Comfort Systems,

Inc.

• Improper positioning of the logs, glass door or decorative

rock.

• Installation and/or use of any component part not manufactured

or approved by manufacturer.

INTRODUCTION

Содержание DVD32FP3 Series





















































Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVD32FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды