White Mountain Hearth DVD32FP3 Series Скачать руководство пользователя

Страница: 30 / 52

Page 30

17333-15-0806

INSTALLATION

1. Unpack vent components and check that all items are included.

2. Check to see that the vent spacer springs are located around the

ﬂue vent at 8" and 12" intervals along its length. See Figure A.

If not, stretch the spacer springs to about 15" long and wrap them

around the ﬂue, then interlock the ends of each spring about 2".

See Figure B. Maintain equal distance between spring spacers.

3. Remove the 6-⅝" dia. Vent collar from the fireplace. Replace this

collar with the 7" dia. Flex Vent adapter collar provided with the

vent kit.

4. Slide the Flex Vent flue pipe into the Outer Flex Vent pipe.

5. Install the Wall Firestop/Thimble assembly as required through

the wall. Refer to the venting charts in the fireplace manual to

determine the proper height and size of the vent opening. The

minimum opening should be 9" wide by 11" high. The minimum

combustible clearance from the horizontal vent is 1" from sides

and bottom, and 3" above the vent pipe. See Figure D.

6. In most cases, after determining the length of the vent that is

needed, it may be easier to install the flue and outer vent pipes to

the Termination Cap first, then from the outside, feed the venting

through the wall to the fireplace.

7. If the venting is to long, trim off any excess vent before attaching

the vent end connectors.

8. Attach the Termination Cap to the outside of the house.

9. Prior to making the vent connections, apply high temperature

sealant (1000 degree F min.) to the vent connections before

securing with the band clamps provided. Note: the flue pipe end

without the adapter

is to be installed to the Termination Cap.

10. Apply sealant to the outside of the flue pipe adapter and connect

to the flex flue pipe. Then insert the adapter into the fireplace flue.

Secure flue adapter to the fireplace flue with a minimum of two

screws provided. See Figure C.

11. Attach the Outer Vent pipe to the 7" dia. Collar on the fireplace

with a large band clamp provided. Sealant may also be used on the

outer vent connections.

12. Check all vent connections for tightness. Make sure horizontal

venting has the proper rise and combustible clearances required.

Refer to venting charts in fireplace instruction manual.

(203 mm)

4 FLEX

VENT PIPE

SPACER

SPRING

FIGURE B

””

”

FLEX OUTER VENT

FLEX FLUE PIPE

SPACER

SPRINGS

FIGURE A

Top of Vent

Combustibles NOT

allowed in shaded

area

(25 mm)

”

Diameter

intake vent

”

Diameter flue

(25 mm)

(76 mm)

FIGURE D

Flex venting can be installed either vertically or horizontally off of the DVD Series ﬁreplaces. When installing a horizontal vent run from top

connections, maintain at least ½" rise for every 12" of vent run. When venting horizontal off the rear vent connections, allow a minimum rise

of 2". Refer to Figure 42 when mounting termination near vinyl siding.

CAUTION: Always stretch and secure venting with wire or metal strapping to ensure that the horizontal runs do not sag.

If space permits, it is generally easier to attach venting in the top vent conﬁguration.

Because of sharp edges, always use gloves when handling the ﬂex vent components.

Vent connections should overlap a minimum of 1" for proper sealing.

Always follow the general venting requirements for vent terminal location, vent lengths, and clearance to combustible materials.

The

DVVK-4F FLEX VENT KIT

includes the following components:

• (1) Horizontal Termination Cap

• (1) 4-foot section of Flex vent with spacers (4" ﬂue/7" outer

pipe)

• (1) 4" dia. Flue adapter collar

• (1) 7" dia. Outer Vent adapter collar

• (1) Wall Firestop/Thimble Assembly

• Hardware pack that includes band clamps and screws

BAND CLAMP

4 DIA. FLUE

ADAPTOR

COLLAR

4 DIA. FLEX

FLUE PIPE

7 DIA. FLEX

VENT PIPE

APPLY HIGH

TEMPERATURE

SEALANT

7 DIA. INLET

ADAPTOR COLLAR

(WITH GASKET)

FIGURE C

”

DVVK-4F FLEX VENT INSTRUCTIONS

Содержание DVD32FP3 Series





















































Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды

White Mountain Hearth DVD32FP3 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание DVD32FP3 Series

Отзывы:

Похожие инструкции для DVD32FP3 Series

Бренды по названию

Популярные бренды