Wheatstone Corporation EMX Скачать руководство пользователя

Страница: 28 / 63

checked for all sources so that no channel has to be turned on to feed the

Off Line bus.
Mix Off Line – This setting allows one to create a bus-minus for a non-

Telco source. It is only active when Telco Source is unchecked. When this

setting is checked, the channel’s bus-minus is fed the Off Line bus while

the channel is off. When the source channel is turned on, the bus-minus

switches to the Bus Minus/Base Mix setting.
Telco Source – When checked the console identifies the source as a Telco

or a 4-wire device (e.g., a caller or remote). Examples of Telco devices are

phone hybrids, ISDN interfaces, POTS codecs, IP codecs, and 2-way

radios. Each Telco device has a From Network audio signal which connects

to the console channel and a To Network audio signal that is returned to

the Telco device which is typically that channel’s bus-minus signal.

When a Telco Source is taken on a fader channel, one bus assignment

button blinks to indicate the bus (Off Line, PGM 1, PGM 2, PGM 3, or PGM

4) that’s currently being returned to the Telco device (the To Network

signal). The correct channel’s bus-minus signal can automatically be

connected to the output connected to the Telco device by using Associated

Connections (see page 35 for details on using Associated Connections).

Studio Mutes

Microphones are identified by setting the source to mute one or more

monitor outputs when their channel is turned on. Figure 3-11 shows the

typical settings for Control Room microphones. Both CR and Cue are

checked to mute those speakers when a CR Mic is turned on. For mics

located in a separate talk studio, typically only Studio is checked, unless

cue is being fed to that studio, then both Studio and Cue are checked.

Typically, the HDPN output is not checked so it normally is not muted by

any source.

Figure 3-11 VDips Page Tab Settings for a Control Room Mic

Studio Tallies

Each mic triggers a tally output by checking one of the Studio 1 – Studio

4 Tallies. If no Studio Tally is checked, the mic status indicators on the

channel displays are not shown and the On Air indicator in the meter

bridge does not light up when the mic channel is turned on. Tally 1 is

typically used for the Control Room and Tally 2 is typically used for the

Talk Studio. Tallies 3 and 4 are available to trigger warning lights at two

External locations with hot mics like an announce booth or a newsroom.

The four studio tally commands are labeled: Studio 1 In-Use up to

Studio 4 In-Use in PR&E Navigator. These commands are typically used to

trigger LIO outputs on the Mix Engine, Razor, or M4IP-USB Blade to

activate outboard warning light interfaces like a Henry Superelay, a

Sonifex On-Air light, or M!ka mic arm lights. The Studio 1 In-Use up to

Studio 4 In-Use commands can also drive SLIO commands to trigger any

WNIP device connected to the EMX. See page 41

for details on assigning

LIO and SLIO output logic in PR&E Navigator.

Bus-Minus/Direct Out

The EMX has an internal mono signal associated with each fader channel

(labeled as sources EMXBM01 up to EMXBM16, EMXBM20, or EMXBM28).

These signals are most often used to create a Bus-Minus signal (hence the

BM in their names) used with callers and remotes. But these signals can

alternately be used as Direct Outs that could feed that source to an

outboard FX unit, an air skimmer, or a system monitor.

The check boxes in this section set which type of signal is generated

when the source is assigned to a checked channel. For a Telco device, no

check boxes should be checked so that a bus-minus signal is automatically

created when the Telco device is dialed up on any fader.

When one or more boxes are enabled, and the source is taken on one of

the enabled channels, a Direct Out signal for that channel is created.

Note: The Direct Out audio is also affected by the settings in the

Direct Out Pre Fader and Direct Out Pre On sections. If Mix Off Line

is checked, no Direct Out boxes should be checked.

Bus Minus / Base Mix

This setting is only used when Telco Source is unchecked and no

channels are checked in the Bus-Minus / Direct Out section. This setting

selects which bus (PGM 1, PGM 2, PGM 3, PGM 4, Aux Send 1, or Aux Send

2) feed that channel’s bus-minus when the channel is turned on.

Direct Out Pre Fader

When enabled for the same channel numbers as set in the Bus-Minus /

Direct Out section, the Direct Out audio is sent at a fixed level (same level

as the cue bus). When unchecked the level feeding the Direct Out is

controlled by the channel fader.

Содержание EMX
































































Результаты поиска

Содержание EMX

Отзывы:

Похожие инструкции для EMX

Бренды по названию

Популярные бренды

Wheatstone Corporation EMX, Руководство пользователя

Результаты поиска

Содержание EMX

Отзывы:

Похожие инструкции для EMX

Бренды по названию

Популярные бренды