Westomatic Eco Encore страница 90 Скачать руководство пользователя | Manualshive

Страница: 90 / 150

background image

89

CHILLER UNIT – TROUBLESHOOTING

Warning:

Care should be taken when working on live equipment; 240Vac is present at the
Chiller unit.

PROBLEM

CAUSE

SOLUTION

NO WATER IS
DISPENSED DURING
A VEND

LOW WATER LEVEL
IN CUP

WATER RUNNING
WARM

No output to
valves

Low mains
water supply

Programmed
Incorrectly

Thermostat
Open circuit

Compressor not
running

Compressor
running But not
chilling

The Cold water inlet valve is operated via
SKT12/1 from the CPU and splits off to
the dispense valve located on the top of
the fridge. Check for 240Vac output
when taking a cold drink.

Increase the water flow rate to the fridge
by adjusting the Water regulator.

Increase the flow time via address 412.

Check that 240Vac from the PSU is
reaching the thermostat. Check the
output of the thermostat is also at
240Vac. If there is no voltage at the
output replace the thermostat.

Check 240Vac to the compressor.
Replace the unit if there is voltage to the
compressor and it is not running.

Loss of gas within the compressor
Change the unit.

«
...
88
89
90
91
92
...
»

Содержание Eco Encore























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Eco Encore

Бренд: Fellowes Страницы: 4

Бренд: Necchi Страницы: 40

Бренд: Singer Страницы: 74

Бренд: ELNA Страницы: 76

Бренд: Singer Страницы: 46

Бренд: MGA Entertainment Страницы: 1

Бренд: Janome Страницы: 43

884-xxx-M series

Бренд: Dürkopp Adler Страницы: 40

Бренд: Nintendo Страницы: 5

Бренд: Pfaff Страницы: 36

Бренд: Duerkopp Adler Страницы: 154

Бренд: Shark Страницы: 41

Бренд: DS Produkte Страницы: 52

Бренд: JUKI Страницы: 2

Бренд: JUKI Страницы: 4

Auto-Logic KX-F115

Бренд: Panasonic Страницы: 34

Facsimile UF-590

Бренд: Panasonic Страницы: 162

DX 1000 - PanaFax B/W Laser Printer

Бренд: Panasonic Страницы: 200

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды