background image

 

 

 
 

47

SET-UP FREE VEND/SUPPLEMENTARY DISCOUNT PERIODS – Addresses 250 
to 255 
 

Up to six free vend OR six supplementary discount periods may be 
programmed although the two are mutually exclusive, i.e. if any free vend 
periods are programmed, the discount feature cannot be used, and vice versa.  

 

FREE VEND PERIODS 

 

During these periods, all drinks may be free vended, or, if required, a limited 
selection of drinks may be free vended. 
The drinks available during a timed free vend period are determined by the 
"Set-up selection range", refer to section 9 ‘Drink selection set-up addresses’. 
 
Each active selection can be programmed to:- 

1.  Timed free vend available.          
2.  Timed free vend not available. 

 

The content of each selection Address for the above options will vary 
dependant on the drink type. Refer to section 9 ‘Drink selection set-up 
addresses’. 
 
FREE VEND PERIODS (CONTINUED) 
At the start of a free vend period, the processor will respond with an audible 
tone of 1 second duration. If all active selections are being free vended, the 
external display standby message will change to read FREE. If, however, any 
selection is to remain as a pay vend, the external display standby messages 
will not change. 
 
PROGRAMMING FREE VEND PERIODS 

 

When programming free vend periods, if the duration of the period is less than 
24 hours, the individual day numbers of which the period is to be active are to 
be programmed (Sunday = Day 1 to Saturday = Day 7, 0 = all days). If, 
however, the period duration is greater than 24 hours, i.e. to cover a weekend, 
only the day on which the period is to start should be programmed. The 
duration of the period is also to be programmed in hours and minutes. The 
maximum duration time = 99 hours 99 minutes. 

 

Example 1:

  A free vend period is required from 10.00 a.m. to 11.30 a.m. on 

Monday to Friday only. 

 

Enter ‘Service’ mode:- 

1.  Enter Address 250 = Free vend period No. 1. 
2.  Press the ‘Vend’ key. 
3.  Enter ‘23456’ - the day numbers of Monday, Tuesday, Wednesday, 

Thursday and Friday. 

4.  Press the ‘Vend’ key. 
5.  Enter ‘1000’ = the start time of 10.00 a.m. 
6.  Press the ‘Vend’ key. 
7.  Enter ‘130’ - the duration time of 1 hour 30 minutes. 
8.  Press the ‘Vend’ key. 

 

Содержание Eco Encore























































































































































Отзывы: