Westomatic Eco Encore Скачать руководство пользователя | Manualshive

Страница: 105 / 150

background image

104

Error code 14 - Triac failure/ master current sense.

Check if any outputs switch on when the machine is powered-up. If so, replace
the processor board. If no outputs switch on, this would indicate a faulty
component driven from SKT 10, 11 or 12.

Error code 19 - Key stuck.

1. Disconnect external keypad and power up the machine, if fault disappears

then check the key pad/loom, replace keypad.

2. If fault persists then replace the Processor board.

Error code 20 - Water Failsafe.

Caused by the operation of the Water inlet valves outside of a vend cycle or the
result of a water leak within the machine. Interrupting power will rectify the
problem and clear down the fault code.

Error code 23 - Fuse blown on Processor Board.

1 Check /replace Fuse 1 (1.0A) and/or Fuse 2 (6.3A) on processor board.

2. Check that triacs being used have an output.

Error code 30 – Dispense arm Jam.

This error will be displayed in the event the arm fails to move or be sensed by
either the home or dispense switches during the vend cycle.

«
...
103
104
105
106
107
...
»

Содержание Eco Encore























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Eco Encore

Бренд: Bandit Страницы: 10

TANK! TANK! TANK!

Бренд: NAMCO Страницы: 144

GPS/F-1006 Series

Бренд: Garudan Страницы: 114

Бренд: Duerkopp Adler Страницы: 78

Бренд: Singer Страницы: 24

The House of the Dead 4

Бренд: Sega Страницы: 202

Бренд: Garudan Страницы: 67

Бренд: Janome Страницы: 46

Бренд: Janome Страницы: 61

Бренд: Duerkopp Adler Страницы: 77

Бренд: JUKI Страницы: 48

Бренд: SunStar Страницы: 42

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды