Weidmuller WI-MOD-400-E Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 113

background image

Rev Version 1.4.1

91

91

Rev Version 1.4.1

Appendix

A - FIRMWARE UPGRADES

You can check the firmware version that is loaded in the module by viewing the home page of the

module’s Web

Server. Firmware upgrades should be performed locally with a PC connected directly to the module. Remote
firmware upgrades are not recommended over the radio link due to bandwidth limitations.

Full Firmware Upgrade

The WI-MOD-xxx-E-5W firmware can be upgraded  using a USB flash drive with  the firmware files installed. A full
USB upgrade is necessary if a patch  file is not available or the existing firmware is a much older version and would
require multiple  patch  files to upgrade to the latest version.

The following procedures provides instructions for performing a full USB firmware upgrade on a WI-MOD-xxx-E-5W .

Requirements

•

USB memory stick

•

Firmware files (contact WEIDMULLER Technical Support to obtain these files)

•

Ethernet cable

•

PC for transferring files

To prepare the USB flash drive

Not all USB flash drives are configured correctly for use as a firmware upgrade drive. Use the following procedure
to check the configuration of the USB drive and re-configure the drive if necessary.

1. Plug USB drive into the USB port on the PC and wait until Windows recognizes the drive and completes the

driver installation.

2. Open the Windows Start menu, choose Run, and then enter

“CMD” to open a command prompt. Type

“diskpart” at the command prompt. This opens the Diskpart utility.

C:\>diskpart

Microsoft DiskPart version 6.1.7601

Copyright (C) 1999-2008 Microsoft Corporation.
On computer: TEST_COMPUTER

3. Type command

“list disk” to list available disks, and identify the USB drive based on the size.

In the following example, the USB drive is a 1911 MB (2 GB) drive, which corresponds to Disk 1.

DISKPART> list disk

Disk ###

Status

Size

Free

Dyn Gpt

--------

-------------

-------

-------

--- ---

Disk 0

Online

232 GB

0 B

Disk 1

Online

1911 MB

0 B

4. When you have identified the USB disk, enter the

“select Disk X” command to select this disk.

Warning:  The commands  that  follow  this  step  can destroy  the contents  of the selected  disk,  make
sure that  you have selected  the correct  drive  before  continuing.  Selecting  the wrong  drive  could
format  your PC

’s hard drive.

DISKPART> select Disk 1

Disk 1 is now the selected disk.

5. Enter the command

“list partition” to check how the USB drive is partitioned.

This command indicates whether the drive is correctly configured for use as a firmware upgrade drive on
the WI-MOD-xxx-E-5W .

«
...
89
90
91
92
93
...
»

Содержание WI-MOD-400-E


















































































































Отзывы:

Нет отзывов

Похожие инструкции для WI-MOD-400-E

Бренд: Campbell Страницы: 90

Бренд: Satel Страницы: 30

Бренд: RACOM Страницы: 157

Бренд: Krüger & Matz Страницы: 52

Бренд: Wood and Douglas Страницы: 32

Бренд: HP Страницы: 14

Бренд: HP Страницы: 30

Бренд: HP Страницы: 50

Бренд: Huawei Страницы: 59

Бренд: Huawei Страницы: 10

Бренд: Huawei Страницы: 16

Бренд: Huawei Страницы: 2

Бренд: Huawei Страницы: 3

Бренд: Huawei Страницы: 20

Бренд: Huawei Страницы: 5

Бренд: Huawei Страницы: 21

Бренд: Huawei Страницы: 22

Бренд: Huawei Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды