manualshive.com logo in svg

WEG SRW 01, Руководство пользователя

Поделиться
Скачать
WEG SRW 01 Скачать руководство пользователя страница 32

Installation and Connection

3-4 | SRW 01

3

XC6 terminal strip:

 

„

Power supply terminal A2.

 

„

Digital outputs – O1, O2, O3 and O4. The outputs O1 and O2 share the common terminal C1.

ATTENTION!

The incorrect application or installation of the SRW 01 may result in damage to its components, faults 
or reduction of the useful life of the product due to wiring or application errors, as well as the incorrect 
setting of the operation mode, rated current of the motor, incorrect selection of the Current Measuring 
Unit (UMC) or Current/Voltage, Measuring Unit (UMCT), incorrect or improper supply source for the 
digital inputs, application of voltage on the terminals T1, T2, E1 and E2.

3.3 RELAY POWER SUPPLY

NOTE!

The power supply must be compatible with the SRW 01 nominal voltage.

The SRW 01 is fed through the terminals A1 and A2 from the terminal strips XC1 and XC6, respectively. 

Supply voltage: 

 

„

110 to 240 Vac and Vdc.

 

„

24 Vac and Vdc.

NOTE!

Check the nameplate on the product to know which model of the control unit was acquired:

 

„

110 to 240 Vac/Vdc or 24 Vac/Vdc supply voltage.

3.4 POWER CABLES

The SRW 01 performs the protection of three-phase and single-phase loads.

The power cable wiring diagram is illustrated in the 

Figure 3.3 on page 3-4

.

(a) Three-phase                                                                                  (b) Single-phase

 

Figure 3.3: 

(a) and (b) Three-phase and single-phase of the Current Measurement Unit (UMC) and Current/Voltage Measurement Unit 

(UMCT)

Содержание SRW 01





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды