P/N # 327985 NEW 9-04-0
6
P/N # 327985 NEW 9-04-0
6
P/N # 327985 NEW 9-04-06
P/N # 327985 NEW 9-04-06
P/N # 327985 NEW 9-04-0
6
Intermediate
section
Lock
section
Bottom
section
Vertical
track
Vertical
track
Alignment sticker
(if applicable)
Alignment sticker
(if applicable)
Alignment sticker
(if applicable)
10B
10D
10A
10C
Center
hinge(s)
Center
hinge(s)
Left graduated end hinge
with short stem track roller
Right graduated end hinge
with short stem track roller
1/4”-14 x 5/8” Self tapping screw locations
1/4”-14 x 5/8” Self tapping screw locations
Left double graduated
end hinge with long
stem track roller
Right double graduated
end hinge with long
stem track roller
10E
10F
10F
1/4”-14 x 5/8” Self tapping screw locations
Stacking Top Section
Tools Required: Power drill, 7/16” Socket driver, 7/16” Wrench, Step ladder, Tape
measure, Safety glasses, Leather gloves
11
IMPORTANT:
THE DIMENSION BETWEEN THE FLAG ANGLES OR WALL ANGLES MUST BE
DOOR WIDTH PLUS 3-3/8” (86MM) TO 3-1/2” (89 MM) FOR SMOOTH, SAFE DOOR OPERA-
TION.
Install a nail to prevent the top section from falling backwards.
Top section
Nail
Door width + 3-3/8” to 3-1/2”
Top of flag angle
1-11/16”
to 1-3/4”
Top
section
Vertical track
against track rollers
Flag
angle
11A
11B
11D
11E
11C
11C
11C
Attaching Horizontal Tracks
Tools Required: Ratchet wrench, 9/16” 7/16” Socket, 9/16” 7/16” Wrench, Step
ladder, Tape measure, Safety glasses, Leather gloves
12
Remove nail that was temporally holding the top section in position.
3/8”-16
Hex nut
3/8”-16 x
3/4” Truss
head bolt
Quick
Install
tab
Key
slot
Quick
Install
tab in
place
12A
12B
12D
12C
Level
Horizontal track angle
Flag
angle
upper
slot
Flag
angle
Horizontal
track
3/8”-16
Hex nut
Horizontal
track angle
3/8”-16 x
3/4” Truss
head bolt
1/4”-20 x
9/16”
Track bolts
1/4”-20
Flange hex
nuts
Horizontal
track
Flag angle
upper slot
12A
12B
12D
12C
Level
Horizontal
track
Level
Level
Horizontal
track angle
Horizontal
track angle
Horizontal
track
12C
WARNING
DO NOT RAISE DOOR UNTIL HORIZONTAL TRACKS ARE SECURED
AT REAR, AS OUTLINED IN STEP A9, OR DOOR COULD FALL FROM
OVERHEAD POSITION CAUSING SEVERE OR FATAL INJURY.
IMPORTANT:
FAILURE TO REMOVE NAIL BEFORE ATTEMPTING TO RAISE DOOR COULD
CAUSE PERMANENT DAMAGE TO TOP SECTION.
Adjusting Top Fixtures
Tools Required: 7/16” / 9/16” Wrench, Step ladder, Tape measure, Safety glasses,
Leather gloves
13
Top fixture
slide
Tighten the (2)
1/4”- 20
Flange hex nuts
Horizontal
track
Top section
Top fixture
base
Intermediate
section
13A
13B
13C
Track roller
Top
section
Top
section
Top section
Intermediate
section
Horizontal
track
Tighten the
5/16”-18
Hex nut
Top
fixture
slide
Track
roller
Top section
(1)1/4”-20 Track bolt and
(1) 1/4”-20 flange hex nut
13A
13B
13C
13D
Strut
9
Содержание 9100
Страница 21: ......