White
Grey
Red
Wire Nut
Connection
Wire
White
Connection
Wire
White/Black
Connection
Wire
Parking Assist
Wires
Safety
Sensor
Wires
Insert Into Appropriate Terminals
®
Models CLLP1 and CLLP1C
Chamberlain Laser Garage Parking Assist
Owner’s Manual
To avoid eye INJURY or damage to product:
• NEVER point the laser at anyone.
• NEVER look directly into the laser beam.
• NEVER disassemble the laser.
• The parking assist is NOT a substitute for safe parking practices.
• Use of controls or adjustments, or the performance or procedures
other than specified can result in hazardous radiation exposure.
• ONLY for use on Chamberlain manufactured garage door openers.
WARNING
CAUTION
WARNING
WARNING
Figure 1
Figure 2
Figure 3
Figure 4
Insert Into Appropriate Terminals
Red
White
Grey
Parking Assist
Wires
Safety Sensor
Wires
Parking Assist
For Service Dial Our Toll Free Number:
U.S.: 1-800-528-9131
Canada: 1-800-654-4736
www.chamberlain-diy.com
INSTALLATION
1. Open yo
u
r garage door and park yo
u
r vehicle o
u
tside of garage.
2. Determine the mo
u
nting location on the ceiling and fasten the
parking assist
u
sing screw and anchor (Fig
u
re 1).
3. Depress tabs
u
nder the wires and temporarily remove the white
and white/black safety sensor wires from the garage door opener.
4.
Stripping the wires prior to installation:
Installing one parking assist:
Separate white and white/black
wires and strip 7/16" (11 mm) of ins
u
lation from parking assist
wires.
Installing two parking assists:
C
u
t 6" (15 cm) of wires from the
end of one set of parking assist wires for
u
se as connection
wires. Separate white and white/black wires and strip 7/16"
(11 mm) of ins
u
lation from both ends of connection wire.
5.
Connecting the wires to garage door opener:
Installing one parking assist:
Twist like colored wires for
parking assist and safety sensors together. Insert twisted wires
into q
u
ick-connect holes: white to white and white/black to grey
(Fig
u
re 2).*
Installing two parking assists:
Separate white and white/black
wires and strip 7/16" (11 mm) of ins
u
lation from the end of
parking assist wires. Twist like colored wires for parking assists,
safety sensors and connection wire together. Sec
u
re with wire
n
u
t. Insert connection wires into q
u
ick-connect holes: white to
white and white/black to grey (Fig
u
re 3).*
*
Please refer to your garage door opener owner’s manual for
proper wire installation.
SET UP AND ADJUSTMENT
1. Drive yo
u
r vehicle into garage and park in the desired location.
2. Activate the parking assist by obstr
u
cting the path of the safety
sensors. The laser will emit a p
u
lsing bright red beam (Fig
u
re 4).
Aim the red beam to a location on the dash or hood that can
easily be seen while seated in the driver’s seat.
NOTE:
The laser will shut off in 1 minute. If you are not finished
adjusting the beam and it turns off, simply obstruct the path of the
safety sensors.
3. Sit in the driver’s seat and confirm that yo
u
can easily see the
location of the red beam. This location is now yo
u
r point of
reference for parking yo
u
r vehicle.
CAUTION: Do not stare
directly into the beam.
Repeat steps for installation on optional
2nd laser accessory kit.
NOTE:
Periodic adjustment of the beam may be required.
OPERATION
1. Open the garage door by activating the garage door opener and
drive yo
u
r vehicle into parking space.
2. The red beam can be seen moving across the hood of yo
u
r
vehicle as yo
u
drive f
u
rther into the garage (Fig
u
re 4).
3. Stop the vehicle when the beam is positioned at the location yo
u
confirmed in step 3 d
u
ring SET UP A
N
D ADJUSTME
N
T.
NOTE:
The laser is activated every time you drive into your garage.
The laser will shut off in 1 minute. A residual reflection of the red
beam from the windshield may appear on walls or objects in your
garage. When operating a vehicle, always ensure that there are no
objects on the floor of the garage or in the path of your vehicle. The
parking assist is not a substitute for safe parking practices.
TROUBLESHOOTING
If the laser does not emit a beam:
• Verify nothing is obstr
u
cting the safety sensors.
• Verify nothing is blocking the parking assist lens.
• Verify that connections are not reversed.
• Verify that all connections are sec
u
re.
• Confirm that the parking assist is aimed toward the garage floor.
• Obstr
u
ct the path of the safety sensors and look for the red spot
on the garage floor.
Please refer to yo
u
r owner’s man
u
al for additional information on
yo
u
r garage door opener and the safety sensors.
CAUTION
ATTENTION
132C2469-1
LASER RADIATION
DO NOT STARE INTO BEAM
RAYONNEMENT LASER
NE PAS REGARDER DIRECTEMENT
LE RAYONNEMENT LASER
Maximum power output: < 1mW @ 635 - 670nm
Puissance de sortie maximum: < 1mW @ 635 - 670nm
CLASS II LASER PRODUCT
APPAREIL AU LASER DE CLASSE II
This Class B digital apparat
u
s complies with ICES-003.
Wire Nut
Parking Assist
Scre
w
6ABX1-1/4"
Anchor
CARTON INVENTORY
