Watt Drive V3000-015HF Скачать руководство пользователя страница 112

Страница: 112 / 180

Explanation of Function

Seite 112 / 180

A044/A244/A
344

: Control method

C001 - C008 : Intelligent input selection
H005/H205

: Speed response

H050/H250

: PI proportion gain

H051/H251

: PI integration gain

H052/H252

: P proportion gain

H070

: PI proportion gain for

it hi

A044/A244/A
344

: Control method

C001 - C008 : Intelligent input selection
H005/H205

: Speed response

H050/H250

: PI proportion gain

H051/H251

: PI integration gain

H052/H252

: P proportion gain

H070

: PI proportion gain for

CONTROL GAIN SWTCH FUNCTION (CAS)

When sensorless vector control, 0Hz sensorless vector control,

or vector control with sensor is selected in control method, this

function can set and change two kinds of gain ,time constant in

speed control system. (proportion, integration compensation)

When control gain switching is selected in intelligent input

selection, gain which is set to H50, H250, H51, H251, H52,

H252 is selected if signal OFF, and gain which is set to H70,

H71, H72 is selected if signal ON.

When control gain switching is not selected in intelligent input selection, same gain is selected as gain in case of signal OFF.

Setting item

Function code

Setting range

contents

Control method selection

A044/A244/A3
44

03
04
05

SLV (A344 is not)
0 Hz domain SLV (A344 is not)
V2 (A344)

Intelligent input selection

C001 - C008

CAS : control gain switching

Speed response

H005/H205

0.01 - 99.99

Unit : no dimension

PI proportion gain

H050/H250

1.0 - 999.9/1000

Unit : %

PI integration gian

H051/H251

1.0 - 999.9/1000

Unit : %

P proportion gain

H052/H252

1.0 - 999.9/1000

Unit : %

PI proportion gain for
switching

H070

1.0 - 999.9/1000

Unit : %

PI integration gain for
switching

H071

1.0 - 999.9/1000

Unit : %

P proportion gain for
switching

H072

1.0 - 999.9/1000

Unit : %

P / PI SWITCHING FUNCTION(PPI)

When sensorless vector control, 0 Hz domain sensorless vector,

or control vector with sensor is selected in control method,

this function can change and use control (compensation) method

of speed control system to proportion integration compensation

and proportion compensation.

When P / PI switching is selected in intelligent input selection,

proportion integration compensation is selected if signal is OFF,

and proportion compensation is selected if signal is ON.

When P/PI switching is not selected in intelligent input selection, proportion integration compensation is available.

Relation code

Содержание V3000-015HF





















































































































































































Результаты поиска

Содержание V3000-015HF

Отзывы:

Похожие инструкции для V3000-015HF

Бренды по названию

Популярные бренды

Watt Drive V3000-015HF, Руководство пользователя

Результаты поиска

Содержание V3000-015HF

Отзывы:

Похожие инструкции для V3000-015HF

Бренды по названию

Популярные бренды