Volvo SDLG LG936L Скачать руководство пользователя страница 69

Страница: 69 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

When the starting switch is in the ON position,

the high beam of front headlight is lightened if

the switch group turns to OFF and put it up; the

head light, tail light and back light is lightened if

the switch group turns to the position of ‘

’ or

‘

’. The high beam of front headlight lights if put it up.

Control of high and low light

When the starting switch is in the ON position and switch group turns to the position of‘

, the

low beam of front headlight is lightened; the high beam of front headlight is lightened when put

the switch down.

Control of turning lamp

The left turning lamp is lightened when the switch is put forward, and the right turning lamp is

lightened when the switch is put backward.

Notice:

The turn indicator lamp is lightened when operate the switch. After the operation of turning finished,

please put back the switch by your hand.

Rocker Switches

The rocker switch includes rocker switch on gauges and the one on right front side of the cab top. The

switches on the gauges refer to

1.1 Control System and the Gauge Figure 3-5

in this chapter. When

the start switch is at

position, the spray, rain wiper, rear lighting lamp, front lighting lamp, rear

headlight, warning lamp are under control; the rocker switch at right front side of the cab top refers to

the figure below, when the start switch is at

position, the unit heater, the spray, front and back

headlight lamp, rear lighting lamp, front lighting lamp

，

back light, warning lamp and rain wiper will

be controlled separately by this switch.

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды