Volvo SDLG LG936L Скачать руководство пользователя страница 86

Страница: 86 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

3.3.4 Braking

Never

put your foot on the brake pedal unless necessary.

Never

press the brake pedal again and again unless necessary.

Never

try to stop the engine and put the high-low speed control lever and the fore-and-aft control

level in the

neutral

position while driving down sloping ground.

△

WARNING

Never

use the control lever of the manual brake switch to

brake or slow the speed of the machine while running

unless in an emergency.

3.4 Stopping

3.4.1 Steps to Stop

Release the accelerator, and press the brake pedal to

stop the machine. Put the gear control lever in the

neutral

position.

After safely stopping, push the parking brake switch to lock the machine in place.

Level the bucket and other equipment to the ground.

Stop the machine on the level ground where there is

no danger of stone falling, coasting or flooding. If it

is necessary to stop the machine on a slope, wedge

the wheels to prevent movement.

After stopping, let the cooling water out. The

temperature is below 0

℃

, if antifreeze is not added. Please refer to

3.5.3 Operation in Cold

Weather

in this chapter.

3.4.2 Steps to Stop Engine

Let the engine run freely for 5 minutes to cool all the parts equally.

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды