Volvo SDLG LG936L Скачать руководство пользователя страница 84

Страница: 84 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

normal position. After that, start again, otherwise there may be some problem.

When the engine oil pressure does not reach the designated value, the high running speed of the

engine will induce a high temperature and the turbo charger may be broken.

Use the equipment control levers to let the preheated hydraulic oil circle in hydraulic tank and

pipes, so that way the hydraulic parts can warm quickly.

Keep the engine at an idle speed for several minutes after starting. Increase the speed to

1000~1200r/min gradually, and then enter the partial load running status. Pay attention to the

value of the gauge.

Do not let the engine run at high speed or low speed more than 20 minutes in the idle status.

If the engine has to run at idle status, the machine should be loaded from time to time or the

engine should run at the middle speed.

3.3 Running

3.3.1 Driving

Make sure there is no other person in, on or around the

machine or around to prevent accident. And keep the

machine under control.

Raise the lift-arm. Keep the bucket backwards, and

keep the motor running.

Put the gear control lever at forward I or backward I

position.

Press the brake pedal; press the parking brake level

to release the brake status.

Release brake pedal, and step on the accelerator
pedal slowly to drive the machine forward or
backward.

It is safe to drive only when the brake pressure is
over the specific value of 0.45MPa.

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды