Volvo SDLG LG936L Скачать руководство пользователя страница 49

Страница: 49 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

8.15 Electric System

A professional person with a proper license must maintain the electric system.

Connect the grounding cable last to prevent an explosion due to electric sparks near the battery

when adjusting outside power.

Remove the start up key before repairing the electric system.

8.16 Maintenance of Storage Battery

Oxygen and hydrogen may be generated during battery charging because the electrolyte of the storage

battery contains vitriol. So mis-operation of the storage battery may lead to severe injury or fire.

Please do as follows:

Keep kids away from the battery. Wear safety glasses and rubber gloves to deal with the battery.

If vitriol gets in the eyes or on the clothes or wash with lots of water and go to hospital if hurt

severely.

Keep fire away from the battery during charging because the generation of oxygen and hydrogen

may cause an explosion. Prevent circuit from shorting.

Keep fire away from the crust on the battery because it is flammable.

Store the battery under dry, clean and well ventilated circumstances with temperatures between

5~25

℃

. Prevent sun light irradiation. Keep the battery 2m away from a heat source. The battery

will be affected by high temperature.

Never

reverse and put horizontally. Prevent damage by too much pressure.

The storage life of a battery is 6 months under room temperature without charging. If over 6

months, please charge before use.

Pay attention to the labels on equipment before installation to prevent accidents.

Spread vaseline on the poles to prevent erosion. The wire connections should be firm and

credible.

Never

hammer the wire pole which may cause the leak of vitriol.

Connect the positive pole of the storage battery with the negative pole of the machine first, and

then connect the negative pole of the storage battery with the positive pole of the machine.

Put the battery on the shaft using the upside fixing method or downside fixing method to prevent

destruction caused by loosening.

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды