Volvo SDLG LG936L Скачать руководство пользователя страница 71

Страница: 71 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

Warning Button Switch:

When this button is pushed down, all the turning lamps will blink for an emergency circumstance,

sending light to warn the other vehicles and passersby. Press the button once again and the button

springs back, so all the turning lamps will stop blinking.

Rain wiper Switch:

Press bottom side, rain wiper will work; press top side, the rain wiper will stop.

Water Spraying Switch:

Press bottom side, spray water to the front glass of the cab; press top side, stop spraying.

Top Lamp Switch:

This switch is behind the ceiling lamp in the operator

cab.

Press

position to turn it on.

Press

OFF

position to turn it off.

Turn it

OFF

during driving.

Fan Switch:

Press the bottom side, for low air speed;

Press the top side, for high air speed;

Press the middle of the button, and the fan will stop.

Horn Switch:

Press the button in the middle of the steering wheel, and the horn will sound.

Power Switch

The switch locates in the right battery box. The power of

the whole vehicle is shut off when the switch turns to the

‘ ’ position; The power of the whole vehicle is turn on

when the switch turns to the ‘ ’ position. Please shut the

power switch if park the vehicle for a long time. The

position shown in the figure is the state of shut off.

1.2.3 Steering Wheel

The steering wheel is in the operator cab. Refer to

1.1 General View of Controls and

Gauges Figure 3-1

in this chapter. The steering wheel and steering unit are connected.

Turning the steering wheel clockwise, the machine turns right; turning the steering wheel

counter-clockwise, the machine turns left.

The features are listed below:

The rotation angles of the steering wheel and the machine are not equal. If the steering wheel is

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды