Volvo SDLG LG936L Скачать руководство пользователя страница 53

Страница: 53 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

Slope boards should be strong enough with sufficient length and width to form a safe slope. The

angle with the ground should not be larger than 15

. Keep a safe distance between slope board

and board, board and machine.

Make sure the height of the two sides of the board is uniform to ensure firm orientation.

Keep the board surface clean, free of lubricant, oil, ice and loose materials. Clean the dirt off the

tires.

Never

turn around on the slope board. If it is necessary, turn outside the board and then drive

back.

Lock the direction mechanism after assembly, wedge the tires and tie the machine tightly with

cords.

9.2 Transportation on the Ground

Obey the rules about weight, height, width and length prescribed by national and local laws for

transporting the machine using a tow truck. Obey the traffic rules.

Know the weight, height, width and length of machine regulation before deciding the transport

routine.

Know the allowed limit of weight bearing when passing bridges or private buildings. Obey the

relative rules when driving on the public roads.

The machine may be unloaded when using other transportation. Please contact Shandong

Lingong Construction Machinery Co. Ltd. or their accredited representative.

9.3 Lifting

Use the hook of the front and rear frame to transport the

machine to ship or train.

Select proper lifting equipment according to the weight

of the loader, otherwise it is dangerous to surpass the

weight limit.

Notices for lifting:

Make sure the loader is in the transporting state.

The front and rear frame should be in the middle

position. Lock the machine using the lock bar to prevent rotation of the front and rear frame

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды