Volvo SDLG LG936L Скачать руководство пользователя страница 100

Страница: 100 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

Oil Replac

②

ement

Park the machine on level ground and run in idle status for about 10 minutes. Trample the

accelerator gently to move the machine slowly to

let the oil drain plug on the wheel side of the

front axle go to the lowest position

Shut engine. Push transmission lever in the

neutral

(“

”) position. Pull the parking brake

lever, and wedge the front and rear wheels.

Loosen the oil drain plugs on the two wheels on

the end sides of the front axle and the oil drain

plugs at the center bottom of the axle shell to

drain oil to the container.

△

WARNING

The temperature of gear oil may be high, so wear protective

clothes, and operate it carefully to prevent injury.

Drain out all the old oil and screw tight the oil drain plugs at the center bottom of the axle shell.

Start engine. Rotate the parking brake switch gently until it rebounds. Move the machine slowly

with gentle acceleration to let the oil drain plug on the front axle move into the horizontal

position, and then shut the engine. Put the transmission lever in the

neutral

position. Pull the

parking brake lever.

Add new gear oil from the oil drain port on the two wheels on the end sides of the front axle and

the oil inlet port at the middle of the axle shell. And then check the oil level again.

Tighten the oil drain plugs on the two wheels on the end sides of the front axle and the oil inlet

plug at the middle of the axle shell.

Replace the rear axle gear oil according to the procedures above.

3.6.5 Adding Oil to Hydraulic Oil Box

Oil Level Check

①

Park the machine on level ground and lower the bucket to the ground. Check whether there is an

angle between front and rear frame.

Check the oil level indicator of the hydraulic oil box on the left side of the machine. The oil level

is normal if the level indicator scale is at a range of ±2 from the middle level. If the oil level

indicator is lower than scale -2 of the middle scale, please add hydraulic oil. Refer to

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды