Volvo SDLG LG936L Скачать руководство пользователя страница 120

Страница: 120 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

110

Check and clean the filter mesh of the oil bowl in the booster pump. Clean the air vent and

replace the brake fluid.

Check if there is leakage in the hydraulic system. Check and clean the air vent of hydraulic

reservoir. Clean the hydraulic reservoir. Replace the filter cartridge of oil-return filter and pilot

filter (if assembled).

Check the clearance and wear condition of the pins and the bushes in every articulated point.

In addition, do the extra maintenance in the first 1000 hours as follows:

Replace the hydraulic oil. And then replace once every 2000 hours.

3.6 Every 2000 Hours (Year) Service

Carry out the periodic maintenance of every 10, 50, 250, 500 and 1000 hours with this maintenance

operation at the same time.

Check performance of the torque converter and gearbox, differentials of front and rear axles and

the wheel side reducers. Disassemble them for checking if necessary.

Check the sealing performance of multi passage valve and hydraulic tank by measuring the

natural sedimentation volume of the cylinders fuel oil, and then check the system pressure. If the

natural sedimentation volume is over than its specified value, replace the multi passage valve or

hydraulic tank. Contact us for details.

Check the welded seams of rim and other stress parts and adjust the deformation.

3.7 Alteration

The maintenance principles listed above are the normal requirements. The maintenance time should

be determined by the closer one between the two the maintenance schedules. If the working condition

is very severe, please shorten the maintenance cycle and increase the maintenance times according to

the real conditions.

3.8 Replace the Air-Storage Tank after 3 Years of Service

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды