Volvo SDLG LG936L Скачать руководство пользователя страница 94

Страница: 94 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

braking power. Another towing machine should be used to pull at the back side to prevent the

towed machine from losing control or turning over.

Start to tow and brake gently, at the low speed, and turn on the warning flash lamp.

The speed for towing the loader should be within 2 km/h. Try to tow the machine to the nearest

repairing garage. If the distance is longer than 10 km or the towing speed faster than 10 km/h, the

front and rear transmission axle must be disassembled or put the loader on towing truck for

transportation.

3.5.3 Operation in Cold Weather

Attention for cold weather

If the temperature is very low, the engine will be difficult to start. And the radiator may be frozen, so

please do as follows:

Use fuel with low viscosity, and add antifreeze into the hydraulic oil and lubricant and coolant.

Refer to

CHAPTER IV 2.2.1 Selection Table of Fuel, Coolant and Lubricant

for

the details of using oil.

Attentions for using antifreeze:

Do not use antifreeze containing formaldehyde, ethanol or propanol.

Never

use any waterproofing agent independently or together with antifreeze.

Never

use antifreeze with different trademarks together.

Replace antifreeze with the proper ratio according to the requirements. Please refer to

CHAPTER IV 2.1.2 Coolant

△

NOTICE

Keep away from fire when adding antifreeze.

Attentions for using the storage battery:

If the temperature goes down, the capacity of the storage battery will go down too. If the

charging ratio of the storage battery is low, the electrolytes may be frozen. Please ensure the

charging ratio is near 100% and try to preserve heat, so that it is easy to start the next day.

If the storage battery is frozen,

never

charge the battery or start the engine. Refer to

CHAPTER I 8.16 Maintenance of Storage Battery

to disassemble the battery and

put it into a hothouse or warm water (

NEVER

let water enter the battery). Warm it to 15

℃

slowly, otherwise an explosion may occur.

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды