Volvo SDLG LG936L Скачать руководство пользователя страница 93

Страница: 93 / 130

Operation & Maintenance Manual

──

LG936L Wheel Loader

(6)

Striking Operation

Tilt the bucket to let the blade touch the ground.

For hard ground, put the lift arm control lever in the

float position; for soft ground, put the lift arm control

lever in the neutral position.

Use reverse gear to strike the ground with blade.

(7)

Towing Operation

△

WARNING

Before towing, the tires must be blocked by the parking brake to

prevent the machine from rolling.

During towing, be careful to prevent severe and fatal injury.

If possible, the engine of the towed machine should keep the engine running to ensure braking

and turning is possible.

If the towed machine engine can not start, disassemble the front and rear transmission axle. If the

machine can not turn, disassemble the steering cylinder.

The connection hole of the rear frame at the inner side of the rear wheel can only be used for

lifting and binding, but not for towing.

If there is no braking system for the towed machine,

never

use soft towing but use fixed towing

or use towing bar. Connect the towing bar to the towing pin at the back of the loader.

If there is no braking system on the towed machine, no one is allowed to stay on it.

Check whether the towing rope and towing pin are strong enough to suffer the weight of the

towed machine. If machine will pass over clay ground or go up a slope, two towing ropes and

towing pins should suffer at least 1.5 times the weight of the towed machine.

Try to decrease the towing angle of the towing rope to ensure that the angle between the towing

rope and the towed machine is within 30°. The height of the towing points of the two machines

should be close.

The connection between the towing equipment and the machine should be strong.

The weight of the towing machine should be heavier than the towed one, and have enough

traction power and braking power to be able to pull or brake two vehicles going up and down a

slope.

When towing the machine down a slope, the machine should have sufficient traction power and

Содержание SDLG LG936L



































































































































Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды

Volvo SDLG LG936L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SDLG LG936L

Отзывы:

Похожие инструкции для SDLG LG936L

Бренды по названию

Популярные бренды