Vmac G300003 Скачать руководство пользователя страница 61

Страница: 61 / 100

VMAC

– Vehicle Mounted Air Compressors

VMAC Technical Support:

1-888-241-2289

VMAC Knowledge Base: www.kb.vmacair.com

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

Engine will not start.

Fuel lever off.

Turn fuel lever on.

Starting with pressure in
the compressor.

Check blowdown function.

Compressor temperature
too high.

Diagnose and repair.

Compressor temperature
switch faulty.

Replace switch.

Low engine oil.

Add oil to engine.

Low fuel in engine.

Add fuel to engine.

Spark plug gap.

Replace spark plug.

Engine air intake
restricted.

Remove restriction / replace air
filter.

Engine exhaust system
plugged or restricted.

Clean or replace exhaust / spark
arrester.

Fuel bowl / filter plugged
or restricted.

Clean or replace.

Battery discharged.

Charge or replace battery.

Starter failure.

Replace starter or use recoil pull
start.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

Pressure relief valve
venting below 200 psi.

Defective pressure relief
valve.

Replace pressure relief valve.

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

Air leaking from small
hole in inlet valve
regulator cap.

This is normal and as per
design.

None required.

Table 5

– Trouble shooting table

Содержание G300003





































































































Результаты поиска

Содержание G300003

Отзывы:

Бренды по названию

Популярные бренды

Vmac G300003, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание G300003

Отзывы:

Бренды по названию

Популярные бренды