Vmac G300003 Скачать руководство пользователя

Страница: 20 / 100

VMAC

– Vehicle Mounted Air Compressors

VMAC Technical Support:

1-888-241-2289

VMAC Knowledge Base: www.kb.vmacair.com

System Controls and Features

The Gas Engine Driven 30 CFM Air Compressor includes the following
controls and features (Figure 6):

•

Electric key start with recoil pull start backup.

•

Manual choke.

•

Compressor overtemperature switch (shuts down the engine).

•

Intelligent throttle which increases or decreases engine rpm based on air
demand (reduces fuel consumption when no air is needed).

•

Automatic system pressure unload with manual override (when the
system is “unloaded”, engine speed can be reduced, decreasing engine
noise, emissions and wear and tear, while increasing fuel efficiency).

•

Hour meter (runs any time the engine is running).

•

Automatic blowdown (depressurizes the system when it is shut down).

The electric fan on the WHASP Tank can turn on at any time.
This is normal operation.

Figure 6

– System controls overview

Choke

Fuel shut

off

Hour meter

Key start

Unloader

valve

Recoil

pull start

Содержание G300003





































































































Результаты поиска

Содержание G300003

Отзывы:

Похожие инструкции для G300003

Бренды по названию

Популярные бренды

Vmac G300003, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание G300003

Отзывы:

Похожие инструкции для G300003

Бренды по названию

Популярные бренды