Vmac G300003 Скачать руководство пользователя страница 44

Страница: 44 / 100

VMAC

– Vehicle Mounted Air Compressors

VMAC Technical Support:

1-888-241-2289

VMAC Knowledge Base: www.kb.vmacair.com

Regular Inspection Instructions

Read the

“Maintenance and Repair Safety” section prior to

performing any work on the system (beginning on Page 38).
Wear appropriate Personal Protective Equipment and follow
all industry standard safety practices.

Do not overfill the system. Overfilling the system with oil can
flood the sight glass window and make the system appear
empty.

Inspecting and Adding Compressor Oil



Ensure the vehicle is parked on level ground and that the compressor
system is depressurized and cool to the touch.



Check the oil level in the sight glass and ensure that it is between the
“MAX” arrow and the “ADD” arrow.



If the level is below the

“ADD” arrow:



Remove the fill cap on the tank (above the sight glass).



Using a funnel, pour oil into the fill fitting until the oil level in the sight
glass reaches the “MAX” arrow.



Replace the fill cap and tighten securely.

Figure 29

– Inspecting the oil

Oil fill cap

Sight glass

Oil drain

Содержание G300003





































































































Результаты поиска

Содержание G300003

Отзывы:

Бренды по названию

Популярные бренды

Vmac G300003, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание G300003

Отзывы:

Бренды по названию

Популярные бренды