manualshive.com logo in svg

Vmac G300003, Инструкция по установке, эксплуатации и обслуживанию


Поделиться
Скачать
background image

VMAC 

– Vehicle Mounted Air Compressors

 

VMAC Technical Support:

 

1-888-241-2289 

VMAC Knowledge Base: www.kb.vmacair.com 

46 

Inspecting and Replacing the Drive Belt 

 

 

Read the 

“Maintenance and Repair Safety” section prior to 

performing any work on the system (beginning on Page 38). 
Wear appropriate Personal Protective Equipment and follow 
all industry standard safety practices.

 

 

Check the drive belt for evidence of glazing, cracks, missing or damaged ribs 
or damage to the belt edges and surface. If the drive belt is damaged, install a 
new drive belt.  

Inspect both pulleys and the idler for damage. If any of the components show 
cracks, chipping, impact damage or any other indications of physical damage, 
replace the component.  

If the damage indicates possible misalignment, check the pulley alignment. If 
the pulleys are not properly aligned, check all fasteners to ensure that they 
are properly torqued and that there are no loose or worn components. 

 

Remove the 5 fasteners from the belt guard and remove the belt guard.  

 

Using a 3/8 in drive, remove tension from the drive belt and discard it. 

 

Install the new drive belt. 

 

Tension the new drive belt. 

 

Apply Loctite 242 (blue) to the 5 fasteners and reinstall the belt guard. 

 

Figure 33 

– Inspecting the drive belt

 

 

Description 

Part Number 

Belt (Gates part number K040438) 

1620365 

Tensioner (Ford part number 7C3Z-6B209-D) 

3300036 

Table 4 

– Belt part numbers and tension 

Remove fasteners (5x) 

Содержание G300003





































































































Отзывы:

Нет отзывов

Похожие инструкции для G300003

Campbell Hausfeld FP260200 Operating Instructions And Parts Manual preview
FP260200
Бренд: Campbell Hausfeld Страницы: 24
Clarke 2245316 Operation & Maintenance Instructions Manual preview
2245316
Бренд: Clarke Страницы: 20
CO/Tech VZB-0.14/8-VFL-50 Original Instructions Manual preview
VZB-0.14/8-VFL-50
Бренд: CO/Tech Страницы: 28
Campbell Hausfeld FP209800 Operating Instructions And Parts Manual preview
FP209800
Бренд: Campbell Hausfeld Страницы: 24
AirMan PDS100S-6B4 Instruction Manual preview
PDS100S-6B4
Бренд: AirMan Страницы: 65
Faller 170987 Instruction Manual preview
170987
Бренд: Faller Страницы: 12
Nuvair 8060 User Manual preview
8060
Бренд: Nuvair Страницы: 40
LW Compressors LW 170 D Nautic / AL Operating Instructions Manual preview
LW 170 D Nautic / AL
Бренд: LW Compressors Страницы: 130
Task Force 83691 Owner'S Manual preview
83691
Бренд: Task Force Страницы: 10
L&W LW 300 E Operating Instructions Manual preview
LW 300 E
Бренд: L&W Страницы: 74
L&W LW 320 E AL Nautic Operating Instructions Manual preview
LW 320 E AL Nautic
Бренд: L&W Страницы: 141
Vector AIRPRO VEC258 Owner'S Manual preview
AIRPRO VEC258
Бренд: Vector Страницы: 7
Fini AIBOSS Operator'S Manual preview
AIBOSS
Бренд: Fini Страницы: 40
Ridetech airpod Series Installation Manual & Operation Manual preview
airpod Series
Бренд: Ridetech Страницы: 20
Danfoss Performer S084 Instructions Manual preview
Performer S084
Бренд: Danfoss Страницы: 28
GEA HGX12P CO2 Assembly Instructions Manual preview
HGX12P CO2
Бренд: GEA Страницы: 32
North American Tool Industries 51866 Important Operating Instructions preview
51866
Бренд: North American Tool Industries Страницы: 10
Parkside PKO 400 B2 Operation And Safety Notes preview
PKO 400 B2
Бренд: Parkside Страницы: 90

Бренды по названию

Популярные бренды

Загрузить еще бренды